User manual RUSSOUND CA4.4PI

[. . . ] A/V DISTRIBUTION & CONTROL SYSTEMS Instruction Manual 4-Zone, 4-Source Central Controller/Amplifier TUNER CD TAPE AUX S O U R C E CA4. 4pi VOLUME · ON / OFF · VOLUME · SOURCE SOURCE STORE SOURCE REMOTE SENSOR POWER REMOTE SENSOR 4 ZONE -- 4 SOURCE CENTRAL CONTROLLER / AMPLIFIER ON 1 2 3 4 OFF POWER ZONE CA 4. 4pi 1. Safety Instructions "WARNING" " TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " "CAUTION" " TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] REAR OF · Connect each 845. 1 mini-emitter to the source IR output. Refer to the source number CA UNIT you had written down in list 1. · Remove the adhesive back and position the IR receiver on the product you wish to control. Stick the 845. 1 emitter directly over the source components IR window. The CA4. 4pi will direct the IR command to the source component you wish to control. · Repeat connections until all emitters match the selected sources. 845 EMITTER CASSETTE DECK 845 EMITTER TUNER 845 EMITTER TO OTHER SOURCE 845 EMITTER 7. 7 Connecting the IR Link · When two CA4. 4pi Controllers are to be used in an installation, the IR Link connection is used to pass IR signal between the two units. Use a 1/8", mono, phone plug, male-to-male cable connected from the IR Link on the first CA4. 4pi Controller to the IR Link on the second CA4. 4pi. When connected, you may connect your IR emitters to either unit's IR Remote Output jacks. 7. 8 Keypad Connections · Each keypad connection on the back panel corresponds to the room / zone number chosen for your speakers. Each zone operates independently, so it is very important to connect the keypad to the correct zone keypad input. Remove the connector and strip 1/8" off each end of the wire insulation. Connect each wire 1 thru 8 using a small jewelers screwdriver. At this point it is not important what color wires connect where, however, take note of the color of each wire and number indicated on the connector when connected to the back panel. · Write down the room name to the zone number below. Note: the keypad and the speakers in each room must be hooked to the same zone number. See List 3. PRESET VOLUME LEVEL ADJUSTMENT List 4 ­ Room names should be written below. Zone 1 _______________ Zone 2 ______________ Zone 3 _______________ Zone 4 ______________ List 5 ­Wire color should be written below. Pin 1 ________ Pin 2 ________ Pin 3 _________ Pin 4 _________ Pin 5 ________ Pin 6 ________ Pin 7 _________ Pin 8 _________ NOTE: Preset volume and balance level adjustments can be made via the volume (VOL) and balance (BAL) potentiometers mounted on the keypad's circuit board. 8. Standard Keypad Installation The CA4. 4pi Central Controller Amplifier is offered with standard keypads and BALANCE LEVEL LCD keypads. If you are installing a unit with LCD keypads skip to step 9. ADJUSTMENT 8. 1 Installing the KP Keypads · The best performance is achieved with the keypad away from any direct sunlight. Also consider the convenience when choosing a location. [. . . ] The backlight will change from one color to the other. 7) IR confirmation LED: This LED will flash to confirm the reception of an IR signal from a remote control through the IR receiver. 8) IR receiver: The IR receiver is used to receive commends from an IR remote control. Remote controls used for the source equipment will pass through to the main controller and on to the source equipment. [. . . ]