User manual RUSSOUND CAM66X

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual RUSSOUND CAM66X. We hope that this RUSSOUND CAM66X user guide will be useful to you.

Lastmanuals help download the user guide RUSSOUND CAM66X.


Mode d'emploi RUSSOUND CAM66X
Download
Manual abstract: user guide RUSSOUND CAM66X

Detailed instructions for use are in the User's Guide.

[. . . ] CAM6. 6X-S1/S2 System 6-Zone, 6-Source XM Receiver and UNO Smart Keypads INSTRUCTION MANUAL IMPORTANT SAFEGUARDS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] Each of these color-coded connectors is designated for the speaker set of a particular amplified zone. To avoid confusion, connect one zone speaker set at a time starting with Zone 1, taking care to keep zone and speaker wire identities straight. Note: An 8 Ohm minimum speaker is required for each amplified output. Pull the speaker wire conductors apart so they're separated for the first two inches from their ends. Using a wire stripper, remove 1/4 inch of insulation from each conductor. Twist the strands in each conductor into tight spirals. Remove the modular four-color connector for Zone 1. The color code is as follows: WHITE -- L+ (left channel positive) GREEN -- L- (left channel negative) BLACK -- R- (right channel negative) RED -- R+ (right channel positive) Lift the black lever for each connection until it locks open and insert the proper speaker wire, matching channel and polarity for all four wires. Insert the modular connector into its designated output on the back of the CAM6. 6. Complete the same steps for the remaining zones. Label each set of speaker wires with the zone and location. ANTENNA CAM6. 6 39 INSTALLER MAKING CONNECTIONS Zone Fixed/Variable Audio Outputs The CAM6. 6 has two Zone Audio outputs, on Zone 1 and Zone 2. Each of these zone audio output connections features a stereo line out RCA connection plus a switch to allow for either a fixed or a variable line level output. When set to Variable, the keypad volume level affects this output. In the Fixed position, keypad volume level will not change the output level. The fixed or variable audio outputs can be used if additional amplification is desired (e. g. , Russound R235LS two-channel amplifier). Use quality RCA signal cables to ensure a constant quality audio signal. ANTENNA CAM6. 6 40 INSTALLER MAKING CONNECTIONS 12VDC Home Theater Trigger In/Out 12VDC Home Theater Trigger In This 12VDC Trigger input is used to control Power Management of the audio sources possibly being shared with a home theater system. When the last zone on the CAM6. 6 is turned off, 12VDC presence to the trigger input will prevent the sources that are on from being turned off. The connections for the trigger are made using a twoconductor cable with 1/8" male mini-plug. The tip is positive (+) and the sleeve is negative (-). 12VDC 100mA Trigger Out The 12VDC 100mA trigger out can be used to engage any 12VDC trigger device or component such as the Russound ACT-1 triggered outlet. The connections for the trigger out are made using a two-conductor cable with 1/8" male mini-plug jacks at each end. The tip is positive (+) and sleeve is negative (-). ANTENNA CAM6. 6 41 INSTALLER MAKING CONNECTIONS 12VDC Mute Trigger In/Out 12VDC Mute Trigger In When 12VDC is applied to the Mute Trigger In, the system will fully mute any source connected to the Source Audio Input. [. . . ] If you want each controller to have access to dual tuners, a suggested solution is to use an ST2 Dual Tuner with two CAM6. 6s as shown on the next page. CAM6. 6X (1) Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = 1 CAM6. 6X (2) Controller Setup Menu: Controller ID = 2 Peripheral Setup Menu: Controller ID = 2 A CAT-5 patch cable is use to connect the RNET Link Out of Controller 1 to the RNET Link In of Controller 2. Sunny Sunny Sunny UNO-S1 UNO-S2 ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) CNBC CNBC CNBC UNO-S1 UNO-S2 ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 108 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH THREE TUNERS Sharing an ST2 Dual Tuner with multiple CAM6. 6 controllers (with and without tuners) The configuration below is suitable for 7 to 12 zones that can access the ST2 Dual Tuner and the CAM6. 6X tuner. This configuration uses RCA "Y" cables from the ST2 Tuner source outputs to connect to both CAM6. 6 source inputs. CAM6. 6X Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = All Controllers Source Setup Menu: Basic Setup Procedure: Source # = 2; Source Name = XM; Command Type = Peripheral Source # = 3; Source Name = AM/FM; Command Type = Peripheral Output/Input Switch = Internal Source Output RCA cable connected from Source 1 audio output on CAM6. 6X (1) to Source 1 input on CAM6. 6 (2) RCA cable connected from ST2 Tuner 1 audio output to Source 2 input on CAM6. 6X (1) RCA cable connected from ST2 Tuner 2 audio output to Source 3 input on CAM6. 6X (1) CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 2 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner; Command Type = Peripheral Source # = 2; Source Name = XM; Command Type = Peripheral Source # = 3; Source Name = AM/FM; Command Type = Peripheral Output/Input Switch = Input RCA cable connected from Source 1 audio output on CAM6. 6X (1) to Source 1 input on CAM6. 6 (2) RCA cable connected from ST2 Tuner 1 audio output to Source 2 input on CAM6. 6 (2) RCA cable connected from ST2 Tuner 2 audio output to Source 3 input on CAM6. 6 (2) ST2-XM Tuner Back Panel NEWMARKET, NH U. S. A. ST2 Smart Tuner INTERFACE LINK RS-232 KEYPAD PORTS FM COAX LOOP ANTENNA IR TUNER 2 AUDIO OUTPUT L R ANTENNA IR TUNER 1 AUDIO OUTPUT L R Serial# 12VDC 1. 5A MADE IN KOREA IN OUT RCA "Y" Cable UNO-S1 102. 5 102. 5 RCA Cable RCA Cable ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) UNO-S1 CNBC UNO-S2 CNBC CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 109 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH ST2 DUAL TUNER Sharing an ST2 Dual Tuner with multiple CAM6. 6 controllers (no built-in tuners) This configuration is suitable for 7 to 12 zones that can all access the ST2 Dual Tuner. This configuration uses RCA "Y" cables from the ST2 Tuner source outputs to connect to both CAM6. 6 source inputs. CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 1 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner 1; Command Type = Peripheral Source # = 2; Source Name = Tuner 2; Command Type = Peripheral Output/Input Switch = Input RCA cable connected from ST2 Tuner 1 audio output to Source 1 input on CAM6. 6 (1) RCA cable connected from ST2 Tuner 2 audio output to Source 2 input on CAM6. 6 (1) CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 2 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner 1; Command Type = Peripheral Source # = 2; Source Name = Tuner 2; Command Type = Peripheral Output/Input Switch = Input RCA cable connected from ST2 Tuner 1 audio output to Source 1 input on CAM6. 6 (1) RCA cable connected from ST2 Tuner 2 audio output to Source 2 input on CAM6. 6 (2) ST2-XM Tuner Back Panel NEWMARKET, NH U. S. A. ST2 Smart Tuner INTERFACE LINK RS-232 KEYPAD PORTS FM COAX LOOP ANTENNA IR TUNER 2 AUDIO OUTPUT L R ANTENNA IR TUNER 1 AUDIO OUTPUT L R Serial# 12VDC 1. 5A MADE IN KOREA IN OUT RCA "Y" Cable UNO-S1 Keypads 102. 5 102. 5 RCA Cable RCA Cable CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) UNO-S1 CNBC UNO-S2 CNBC CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 110 TECHNICAL SPECIFICATIONS CAM6. 6X Controller Dimensions: Weight: Power Supply: Fuse Rating: 17"W x 12"D x 3. 5"H (43 x 30. 5 x 9 cm) 18 lbs. (8. 1 kg) 110 or 240 VAC 110V input; F3A H 250V US and Canada 240V input; T1. 25A H 250V Europe Frequency Response: Watts per channel: THD+N: Signal to Noise Ratio: Audio Source Inputs: Input Impedance: Audio Zone Outputs: 20Hz-20kHz +/- 1dB 20 Watts RMS into 8 Ohms <0. 05% >88dB 6 (including internal tuner) 50 kohm 6 Speaker Level (8 ohms) (2 Line level) Max Source Audio Input: Max Zone Variable Line Audio Output: Max Zone Fixed Line Audio Output: Trigger Outputs: Trigger Inputs: XM XM Band: 2332. 5 - 2345 MHz 2. 2 Vrms 2. 2 Vrms 2. 2 Vrms 1 Common. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND CAM66X

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND CAM66X will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag