User manual RUSSOUND ISH1

[. . . ] Don't try to use this product in ways it wasn't designed for. Use indoors only. Don't expose this product to the only by qualified service personnel when: · Liquids have spilled or objects have fallen into the product · The product has been exposed to rain · The product doesn't appear to operate normally · The product is damaged Don't attempt to service the product yourself. If you have any questions, please call Russound at 1. 800. 638. 8055 or 603. 659. 5170. weather or harsh environmental conditions such as continuous sunlight, excessive humidity, or rain. Keep product dry. Don't use the product near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. [. . . ] When running CAT-5 and speaker cables, avoid AC power wiring. If you have to run the cables parallel to electrical wiring, space the cables at least two feet (0. 6 m) from the AC power lines. The hub has 8-pole modular jacks for keypad and door station connections. These connections must be made according to the T568A standard as shown in the diagram below. The hub also uses modular jacks for the link ports. Use a short 8-pole, 4-twisted-pair straight-through RJ-45 patch cable to link hubs together. RJ-45 Using T568A Wiring Standard INSTALLATION ISK2 ISH1 ISPS ISK3 ISK3 ISDR1 Six-zone ComPoint system with Advanced Keypads and an optional Door Strike Release Module 5 INSTALLATION Programming All system programming resides in the ISH1 Hub. For a six-zone system with ISK1 Basic Keypads, programming consists only of setting the doorbell chimes. For a system with ISK2 Advanced Keypads, programming includes assigning zone and door station labels. For a system with more than six zones, programming includes setting hub ID numbers. When multiple hubs are used, the zone and door label settings are initially stored in the hub to which the keypad is connected. Upon exiting the programming procedure, the settings are copied to the other hubs. Hub 1 serves as the master hub for storing all zone and door label settings. Whenever the system power is cycled, the settings are copied from hub 1 to the other hubs. Hub ID numbers In a system with multiple ISH1 Hubs, each hub must have a unique ID number. This is manually assigned on the 4-switch HUB ID DIP before the system is powered up. To assign the ID number, set switches 1 through 3 as shown in table 1. Switch 4 enables a programming mode for updating the system firmware. Leave this switch in the up position for system operation. 6 Hub ID Switch Settings (0 = Down, 1 = Up) Switches Hub 1 Hub 2 Hub 3 Hub 4 Hub 5 Hub 6 Hub ID 1 0 0 0 0 1 1 2 0 0 1 1 0 0 3 0 1 0 1 0 1 FW* 4 1 1 1 1 1 1 *Switch 4 is for firmware updates (0 = Update Mode, 1 = User Mode) Table 1. Hub ID switch settings Doorbell chimes A single 8-switch DIP assigns doorbell chimes for both door stations. Switches 1 through 3 select the chime for door 1 and switches 5 through 7 select the chime for door 2. There are 7 chime options, with a setting for no chime when a separate doorbell system is used. To select the chimes, set the switches as shown in table 2. [. . . ] Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. Before returning a unit for repair, call Russound at 603. 659. 5170 for a Return Authorization number. Write the RA number on the shipping label and ship to: Russound, 5 Forbes Road, Newmarket NH 03857. Russound sells product only through authorized dealers and distributors to ensure that customers obtain proper support and service. [. . . ]