User manual RUSSOUND KPL

[. . . ] Subsequent presses of the Source button toggle through Treble, Balance, Turn On Volume and Loudness. Once an option is selected, the volume up/down buttons are used to adjust settings. The volume indicator bars indicate the option setting, along with setting numbers displayed on the LCD. Treb (Treble): -10 < Treble:Flat > +10 3. [. . . ] VOLUME UP - Raises the volume for the room/adjusts menu items. VOLUME DOWN - Lowers the volume for the room/adjusts menu items. SOURCE SELECT - Press and release scrolls through the available sources. Press and hold brings up the USER MENU for Loudness, Bass, Treble, etc. IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. Also used when the keypad is operated using the CA System remote controls. IR CONFIRMATION/LOUDNESS LED - Blue LED blinks to confirm IR signal reception, and remains lighted when Loudness feature is enabled. POWER - Turns room ON or OFF when pressed once, when OFF, press and hold 4 seconds to turn OFF all zones; button remains lit when OFF if any other zone in the system is ON. SYSTEM INFO - SYS ON indicates other active zones and SHARED indicates the selected source is in use in another zone. 2 3 4 5 6 All trademarks are property of their respective owners. 7 8 5 Forbes Road, Newmarket, NH 03857 tel 603. 659. 5170 · fax 603. 659. 5388 www. russound. com 28-1203 07/29/05 9 KPL Side Panel The KPL setup button and KPSC 12-pin header are located on the right side of the keypad (when facing front). These are covered when a trim plate is installed. 1 OS UPDATE/RUN JUMPER -The pins are jumpered only when performing an OS update on the keypad, and removed during normal operation. 2 3 SETUP BUTTON - Activates information and update menus for the keypad. KPSC PORT - 12-pin header for connecting to KPSC keypad. KPL Back Panel The KPL keypad uses a 110punchdown terminal on the back panel to provide a simple installation and strong connection for CAT-5 cable's eight conductors. Punchdown terminals require the use of a punchdown tool. Attach the CAT-5 cable to the 110-punchdown terminal on the KPL keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly if the terminations deviate from the required connection order. Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Use of the impact tool may propel stray bits of wire and jacket into the keypad's chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed in the junction box. KPL Keypad to CA Controller Connection Each keypad connects to a Keypad Port on the back of the controller (CAA66 controller shown below). Connections are made using CAT-5 cable with an RJ45 connector (wiring scheme shown below). An SA-ZX3 Keypad Splitter can be used to add additional keypads to each zone. Safety Instructions 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] All other servicing should be referred to qualified service personnel. Precautions: KPL Top View 4 OS UPDATE PORT - Used to update the KPL keypad operating system firmware. If an update is released, it will be available online through the Document Center on www. russound. com. Look in the "Firmware and Downloads" section under Multi-Zone product type. The Advanced Programming Cable is available from Russound, Part #2500-521065. Technical Specifications Dimensions: 1. 875"W x 2. 7"D x 1. 47"H (4. 7 x 6. 9 x 3. 7 cm) Fits 1 Gang UL/CSA Approved 18 ci Junction Box 4. 5 oz. [. . . ]