User manual RUSSOUND ST2 REV 1

[. . . ] ST2 Smart Tuner Dual AM/FM Tuner INSTRUCTION MANUAL IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] STEREO or MONO appears briefly on the screen when selecting mode. On a preset, the stereo/mono setting is saved for that preset. This is useful for stations which may have annoying static in stereo mode. Selecting mono will bring in a much stronger signal with less noise but at the cost of stereo sound. Selecting the desired tuner (Note: To change the tuner that is audio-active, you must have some other system control in place to change the source) To control a tuner, push the TUNER 1 or TUNER 2 button. When pressed, these buttons will be backlit green for Tuner 1 and amber for Tuner 2. Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. Selecting Distant or Local Reception Press the LOC/DX button to toggle between Distant and Local mode. DISTANT or LOCAL appears briefly on the screen when selecting mode. In cities, antennas can pick up multipath signals when they bounce off buildings and get doubled. The Local mode limits the noise associated with these reflected signals. Selecting the desired band Push the AM/FM button to switch between AM and FM reception. Recalling a Memory Preset To recall a memory preset, select the desired tuner, press the BANK button to select the desired bank, then press MEM and enter the desired preset number (1 to 6). The memory presets can also be accessed by using the MEM UP and MEM DOWN buttons to scroll through all presets for the selected bank. Selecting the desired frequency Use the Tune Up and Tune Down buttons for manual tuning. To move quickly through the channels, press and hold either of the Tune buttons for more than 1. 5 seconds. To directly select a station, press TUNE, and enter the three- or four-digit station frequency (1071 for 107. 1, etc. ). European regions use five-digit station frequencies. Saving Favorites The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding the FAV 1 or 2 button until "FAV1 (2) saved" appears on the tuner. Stored Favorites are then recalled by pressing either FAV 1 or FAV 2. Frequency Seek The SEEK function is performed by pressing and releasing the SEEK left or right buttons. To seek higher frequency station press SEEK>, and press SEEK< for lower frequencies. SEEK> tuning begins at the current frequency, seeks upward and stops at the next tuned station. Pushing the SEEK> again continues the SEEK function. Once the highest frequency is reached, the tuner continues in SEEK mode at the lowest frequency. 14 ST2 OPERATION UNO-S2 KEYPAD CONTROLS WITH CAV6. 6 CAV6. 6-UNO-S2 Keypad Operation NOTE: To control the ST2 Tuner through the UNO-S2 keypad, the tuner must be configured as a source using the CAV6. 6 programming steps (see page 19) Turning the unit on The tuner is power managed by the CAV6. 6 or other RNET-enabled controller. If the tuner is in standby mode, any button press of the UNO-S2 keypad will bring the tuner out of standby mode. Frequency Scan To scan, press and hold then release . The tuner scans through tuned stations with a 5-second preview before moving to the next station. To end scanning, press again. Selecting a Bank To select a bank, press and hold for bank up or Selecting the desired tuner On the UNO-S2 keypad, press to select either for bank down. [. . . ] Press BAND at "Build Date" to view. Press BAND at "Version" to view. Press TNR SEL to exit the System Info menu. Update Firmware The Update Firmware procedure allows the ST2 tuner's OS firmware to be updated. The procedure is performed using a DB9 serial cable with one end connected to the RS-232 port on the back of the tuner and the other connected to a PC or laptop. [. . . ]