User manual RUSSOUND ST2-KP

[. . . ] For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound. The unit must be returned to Russound at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damage resulting from abuse or from servicing by an agency or person not specifically authorized in writing by Russound. [. . . ] Write this number on the shipping label and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857 Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice. 1 LCD PANEL - 5-character backlit display shows frequency and band (messages scroll twice, then show first 5 characters) FREQUENCY SELECT - Manual station tuning (European frequencies show in . 05 MHz increments) BAND - Selects band (AM/FM); selects Operating Mode (XM) POWER - Turns lighted keypad display on or off TUNER SELECTION - Press and hold to select TUNER 1 or TUNER 2 (unless jumper set for specific tuner) BANK SELECT - Used for bank selection (press and hold) MEM UP/DOWN - Scrolls through memory preset stations for selected bank (press and release) 2 This Procedure is for Factory use ONLY Displays current firmware version HOLD BAND All trademarks are property of their respective owners. 3 4 After update cycle Power 4 Start Update 5 5 5 Forbes Road, Newmarket, NH 03857 tel 603. 659. 5170 · fax 603. 659. 5388 e-mail: tech@russound. com www. russound. com Cycle Power ST2-KP Side Panel The ST2-KP's setup button, OS update pins and hardware tuner select pins are located on the right side of the keypad (when facing front). 1 OS Update/Run Jumper -The pins are jumpered when performing an OS update on the keypad, and the jumper is left on one pin during normal operation. (Typically needed only on a keypad that has never been updated) TNR2 ST2-KP Back Panel CAT-5 Connection The ST2-KP keypad uses a 110punchdown terminal on the back panel to provide a simple installation and strong connection for CAT-5 cable's eight conductors. Punchdown terminals require the use of a punchdown tool. Attach the CAT-5 cable to the 110-punchdown terminal on the ST2-KP keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly if the terminations deviate from the required connection order. Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Use of the impact tool may propel stray bits of wire and jacket into the keypad's chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed into the junction box. 4 Data Rx TTL Level Data Tx TTL Level GND +12VDC Note: Do not put RS-232level signals into the pins. Must use Advanced Programming Cable P/N 2500-521065. Safety Instructions 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to. Follow Instructions - All operating and user instructions should be followed. Water and Moisture - The appliance should not be used near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Wall Mounting - The appliance should be mounted to a wall only as recommended by the manufacturer. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through the openings. 10. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. [. . . ] Care ­ From time to time you should wipe off the front panel with a soft cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel lettering. Keypad to ST2 Connection The ST2 tuner supports up to two ST2-KP keypads. An SA-ZX3 Keypad Splitter can be used to add additional keypads. CAT-5 Cable 5. Mount the keypad in the electrical box and attach the cover plate. The ST2-KP connects to the ST2 tuner with CAT-5 cable. [. . . ]