User manual RUSSOUND ST2-XM 1

[. . . ] 800. 967. 2346 IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] STEREO or MONO appears briefly on the screen when selecting mode. On a preset, the stereo/mono setting is saved for that preset. ST/ MONO or any other button except TUNER 1 or Selecting the desired tuner To control a tuner, push or . When pressed, these buttons will be backlit green for Tuner 1 (XM) and amber for Tuner 2 (AM/FM). Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. TUNER 1 TUNER 2 Selecting Distant or Local Reception (AM/FM only) Press to toggle between Distant and Local mode. DISTANT or LOCAL appears briefly on the screen when selecting mode. Normal operation is in Distant mode. LOC/ DX Selecting the desired band (AM/FM only) Push AM/FM to switch between AM and FM reception. Recalling a Memory Preset To recall a memory preset, select the desired tuner, press BANK Selecting the desired frequency or channel TUNE Use and for manual tuning. To move quickly through the stations or channels, press and hold either of the Tune buttons for more than 1. 5 seconds. TUNE and enter the desired bank number MEM (1-6), then press and enter the desired preset number (1 to 6). The memory presets can also be MEM To directly select a station or channel, press , and enter the two- or three-digit XM channel number, or the three- or four-digit station frequency (1071 for 107. 1, etc. ). European regions use five-digit station frequencies. TUNE accessed by using and presets for the selected bank. MEM to scroll through all Saving Favorites The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding FAV 2 FAV 1 Selecting a mode (XM) Push OK to select an XM operating mode. or Exiting a mode (XM) Push menu. ST/ MONO to exit the XM operating mode selection until "FAV1 (2) saved" appears on the tuner. Stored Favorites are then recalled by pressing either FAV 1 or FAV 2 . 20 ST2-XM OPERATION ST2-KP KEYPAD CONTROL ST2-KP Keypad Operation 1 4 Selecting a Bank Turning the keypad on/off To select a bank, select the desired tuner, then press and hold or to select the desired bank. The bank name will show on the display. To activate the ST2-KP, press . The keypad remains powered until the ST2-XM Tuner is turned off. 1 Selecting the desired tuner 4 Recalling a Memory Preset or To select a different tuner, press and hold . (If the keypad has been hardware jumper-selected to Tuner 1 or Tuner 2, it will not switch between the two tuners. ) The backlight color of the display will be green for Tuner 1 (XM) and amber for Tuner 2 (AM/FM). Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. 2 To recall a memory preset, press and release to scroll through the presets for the selected bank. (Memory presets must be stored for ST2-KP recall) 5 ST2-KP Keypad Display The 5-character backlit display shows frequency and band, plus XM channel and mode information. Messages scroll twice, then display the first 5 characters. Selecting the desired band (AM/FM) to switch between AM or FM band. Push 2 Selecting a mode (XM) to select an XM operating mode. ST2-KP Keypad-Front Panel Push 2 Exiting a mode (XM) 5 Press and release until EXIT is displayed to exit the XM operating mode menu. Selecting the desired frequency or channel Use and for manual tuning. To move quickly or 4 3 3 2 3 1 through the channels, press and hold either for more than 1. 5 seconds. European frequencies show in . 05 MHz increments. 21 ST2-XM OPERATION UNO-S2 KEYPAD CONTROL WITH RNET CONTROLLER UNO-S2 Keypad Operation NOTE: To control the ST2 Tuner through the UNO-S2 keypad, the tuner must be configured as a source using the controller's programming steps. Turning the unit on The tuner is power managed by the CAV6. 6 or other RNET-enabled controller. If the tuner is in standby mode, any button press of the UNO-S2 keypad will bring the tuner out of standby mode. Frequency Seek (AM/FM only) A press on will seek the next higher tune- able station. If a tuneable station is not found, end the SEEK function by pressing Frequency Scan (AM/FM only) To scan, press and hold then release . The again. tuner scans through tuned stations with a 5-second preview before moving to the next station. [. . . ] Each tuner must be set up with a unique source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus. Key Function Note: When using the tuner with an RNET system, do not reassign keypad and remote buttons for tuner control in the controller's Key Configuration Menu. When the tuner is assigned the "Peripheral" command type in the controller's Setup Menu, key assignments and functions are automatically assigned and will operate as shown in the preceding UNO-S2 keypad and SRC2 remote diagrams. 34 TECHNICAL SPECIFICATION ST2-XM Smart Tuner Dimensions: Weight: Power Supply: Frequency Range: 17"W x 8"D x 1. 8"H (43 x 20. 3 x 4. 4 cm) 7 lbs. [. . . ]