User manual RUSSOUND TWIST &TILT

[. . . ] Advantage TWIST & TILT OWNER'S MANUAL Contents Introduction ­ The Russound Advantage . . 4 Impedance Matching for Amplifier and Speakers . . 6 WHO ­ Installer Skills and Tools Required . . 6 WHAT - Speaker Usage and Environment . [. . . ] Incorporating optional IR receivers in Iso-Mount models will require additional wire. Consult the selected IR receiver model's manual for the specific wire needs. Care must be taken to avoid obstacles when running wire. In general, you should pay particular attention to the following: · Avoid locations concealing pipes, heating ducts, and AC wiring in the general vicinity. · Avoid running speaker wires close to house electrical wiring for any distance. If you have to run them parallel, make sure to space the speaker wires at least two feet from the AC line. It is, however, permissible for speaker wires to cross paths with AC line or pass through the same hole together with house wiring if they separate before and after. · Make sure that the entire wire path between speakers and amplifier is clear and not obstructed by a floor or ceiling joist, or a masonry wall which can't be drilled through. Confirm ahead of time that you can drill an outlet hole easily and in an unobtrusive spot to connect wires with the amplifier/receiver. · Label speaker wires at each end "left" or "right" and include room location. This simplifies speaker/receiver hook-up once the speakers are installed. 12 HOW ­ Painting the Speaker Frames and Grilles TO PAINT SPEAKERS THAT HAVE BEEN ASSEMBLED AND INSTALLED: FRAME 1 Remove the speaker grilles from the frames, being careful not to damage the paint. Use a small pointed object and start at the corner or edge of the grille. 2 Remove the scrim cloth by gently separating it from the inside surface of the perforated grille, being careful to keep it clean. 3 Center the included black plastic paint shield over the speaker baffle and press into the frame. BAFFLE GRILLE 4 Paint the outer speaker frame and grille separately. For the grille, Russound recommends a spray application using latex paint diluted 4 to 5:1 with water. If you're using an aerosol spray paint, make sure that you achieve the same coverage on both grille and frame. 5 While the paint is still wet on the grille, and the grille is not in the frame, use a gentle burst of compressed air against the outside surface to clear the fine holes in the metal mesh. Figure 6 SCRIM CLOTH 6 After the paint has thoroughly dried, remove the paint shield from the frame and store for future use. The shield may be held in by a vacuum seal. Pull gently but firmly to slowly break the seal and remove. 7 Reattach the scrim cloth to the grille, starting from the edge and smoothing wrinkles as you go. Note: Speaker frames can become bonded to the wall or ceiling surface paint when they are painted after installation. Use care not to break the surface of the paint when replacing the grille or baffle in the frame. GRILLE Figure 7 13 HOW - Cutting Wall/Ceiling Opening for Speakers HOW - CUTTING WALL/CEILING OPENING FOR SPEAKER The following steps outline how to locate a section of wall between two studs, mark the outer boundaries of the hole, drill a small hole in the center to verify the location and then cut the main hole. [. . . ] Short circuit causing amplifier/receiver to power down or suffer damage For any other speaker performance issues, contact your Russound dealer or call our Tech Services department at 603-659-5170. Specifications Speaker Specifications Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Single Point Stereo SP-S5TT Round In-ceiling 15° Twist & Tilt 7. 25" (18. 4 cm) 5. 25" (13. 3 cm) woven glass fiber dual voice coil Dual 14mm (0. 56") polycarbonate 5 - 50 watts per channel 8 Ohms 91 dB (1W @ 1M w/1kHz) 60Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 8. 75" (22. 2 cm) dia. Single Point Stereo SP-S6TT Round In-ceiling 15° Twist & Tilt 8. 25" (20. 9 cm) 6. 5" (16. 5 cm) woven glass fiber dual voice coil Dual 14mm (0. 56") polycarbonate 5 - 60 watts per channel 8 Ohms 92 dB (1W @ 1M w/1kHz) 55Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 9. 75" (24. 7 cm) dia. Music SP-M5TT Round In-ceiling 15° Twist & Tilt 7. 25" (18. 4 cm) 5. 25" (13. 3 cm) woven glass fiber 20mm (0. 8") silk dome, fluid cooled 5 - 80 watts 8 Ohms 88 dB (1W @ 1M w/1kHz) 55Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 8. 75" (22. 2 cm) dia. 20 Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Music SP-M6TT Round In-ceiling 15° Twist & Tilt 8. 25" (20. 9 cm) 6. 5" (16. 5 cm) woven glass fiber 20mm (0. 8") silk dome, fluid cooled 5 - 100 watts 8 Ohms 89 dB (1W @ 1M w/1kHz) 50Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 9. 75" (24. 7 cm) dia. Music SP-M8TT Round In-ceiling 15° Twist & Tilt 9. 75" (24. 7 cm) 8. 0" (20. 3 cm) woven glass fiber 25mm (1. 0") silk dome, fluid cooled 5 - 120 watts 8 Ohms 90 dB (1W @ 1M w/1kHz) 40Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 11. 25" (28. 5 cm) dia. Specifications Hi-Fi SP-H5TT Round In-ceiling 15° Twist & Tilt 7. 25" (18. 4 cm) 5. 25" (13. 3 cm) woven glass fiber long throw 20mm (0. 8") aluminum dome, fluid cooled 5 - 100 watts 6 Ohms 89 dB (1W @ 1M w/1kHz) 50Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 8. 75" (22. 2 cm) dia. 21 Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Series: Model: Description: Cut-Out: Woofer: Tweeter: Recommended Power: Nominal Impedance: Efficiency: Frequency Response: Frame: Grille: Mounting: Dimensions: Hi-Fi SP-H6TT Round In-ceiling 15° Twist & Tilt 8. 25" (20. 9 cm) 6. 5" (16. 5 cm) woven glass fiber long throw 20mm (0. 8") aluminum dome, fluid cooled 5 - 120 watts 6 Ohms 90 dB (1W @ 1M w/1kHz) 45Hz - 20kHz +/- 3 dB ABS plastic Fine mesh aluminum Bayonet-type with swing-out clamps 9. 75" (24. 7 cm) dia. [. . . ]