User manual RUSSOUND UNO-S2

[. . . ] UNO-S2 Keypad Installation Manual SAFETY INFORMATION UNO-S2 Keypad 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to. [. . . ] When another UNO Systems Keypad selects the same source, a DND icon will appear alerting the user the source is in Do Not Disturb mode. PARTY MODE - Master (Enable/Disable) When in "PARTY MODE" the system is primarily controlled by a "MASTER" Keypad. Party Mode links all rooms to the same source which is selected by the Master Keypad room. Any keypad in the system can become a Master Keypad (if enabled) but only one Master Keypad may exist at a time in Party Mode. Selecting Master Keypad mode from another keypad will transfer Master Keypad control to that room and release it from the first. When the source selected in the Master Keypad room is changed then the source for all rooms changes as well. Volume level changes at the Master Keypad will be reflected in all rooms in Party Mode. Non-Master zones in Party Mode can temporarily override Master Keypad volume level adjustments for their particular room preference. F1 and F2 favorite presets selected from the Master Keypad will be enabled in all rooms in Party Mode. Master Keypad will not change Bass, Treble, or Loudness adjustments for any other rooms other than the Master Keypad room. Every other keypad will still operate its respective bass, treble, balance and loudness adjustments for that room. FRONT (AUX) A/V IN - Enabled/Disabled Allows the system to select a seventh source option through the controller's front panel AUX connection for use with camcorders, game consoles, etc. 9 INSTALLER GUIDE UNO-S2 Keypad Update Port 1 DATA RS-232 DATA RS-232 GND N/C +12VDC 2 1 2 SETUP BUTTON - Activates Installer Setup Mode for the UNO-S2 keypad OS UPDATE PORT - Port used for UNO keypad OS software updates 10 INSTALLER GUIDE UNO-S2 Keypad Rear Panel 2 3 1 4 1 2 3 4 EXTERNAL IR RECEIVER IN CONNECTOR - Connection for external IR Receiver OS UPDATE JUMPER - Selects "Run" or "OS Update" mode RESET BUTTON - Reset whenever changing from RUN to OS update 110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the UNO-S2 Keypad and the CAV6. 6/CAM6. 6 controller 11 INSTALLER GUIDE UNO-S2 Keypad Connections Punchdown Tool Jumper Setting (back of keypad) Punchdown Tool CAT-5 Connections (back of keypad) OS Update Port (front of keypad) 12 INSTALLER GUIDE UNO-S2 Keypad Connections CAT-5 Connection The UNO-S2 Keypad uses a 110-punchdown terminal to provide a simple installation and strong connection for CAT-5 cable's eight conductors. Punchdown terminals require the use of a punchdown tool which has been provided with the keypad kit. Attach the CAT-5 cable to the 110-punchdown terminal on the UNO-S2 Keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly if the terminations deviate from the required connection order. Caution Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Use of the impact tool may propel stray bits of wire and jacket into the keypad's chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed into the junction box. OS Update Port The OS Update Port is is used to update the UNO-S2 Keypad operating system software in the future. When an update is released, it will be available online through the Document Center at www. russound. com. Look for the Technical Documents under Multisource/Multi-room products. [. . . ] Route CAT-5 wire to the junction box from the CAV6. 6/CAM6. 6. Use the supplied 110 punchdown tool to connect each wire to its corresponding color labeled on the punchdown terminal (See page 12 for details). Ensure jumper setting on the keypad is in the "RUN" position. Mount the keypad in the electrical box and attach the cover plate. [. . . ]