User manual RUSSOUND VBHD KIT

[. . . ] Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 9. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 10. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. [. . . ] If water or any other liquid enters the cabinet, take the unit to a qualified service person for inspection. LIMITED WARRANTY The Russound HDTX and HDRX baluns are fully guaranteed for two (2) years from the date of purchase against all defects in materials and workmanship. For this warranty to apply, the unit must be installed and used according to its written instructions. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. Accidental damage and shipping damage are not considered defects under the terms of this warranty. Russound assumes no responsibility for defects resulting from abuse or servicing performed by an agency or person not specifically authorized in writing by Russound. If service is necessary, it must be performed by Russound. Damage to or destruction of components due to excessive power voids the warranty. In these cases, the repair will be made at the owner's expense. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of the service required. Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number. Write the RA number on the shipping label and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket NH 03857 Russound sells product only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product. VBHD Kit Component Video Balun Installation Manual INTRODUCTION The VBHD Component Video Balun Kit contains a pair of active circuitry (powered) baluns for sending component video over a single CAT-5 cable. This kit includes a transmitter and receiver and would be used to distribute video from a central source to a remotely located video device. The benefits of using this kit are that it uses low-costs CAT-5 cable, plus it eliminates ground loops, which may occur when remotely locating sources from displays. Ground loops are seen as lateral "hum" bars scrolling on the display and an audible hum in the audio. KIT CONTENTS 5 Forbes Rd. Newmarket, NH 03857 Tel 603. 659. 5170 · Fax 603. 659. 5388 e-mail: tech@russound. com 28-1247 01/24/06 (1) HDTX transmitter module (1) HDRX receiver module (1) 846C 12VDC 200mA power supply OVERVIEW Component video gives a higher quality picture than composite video or S-video. Component video terminations and cables have three separate sections: yellow, red, and blue. A component video signal has three parts: luminance, hue and saturation. [. . . ] Use hook and loop fastener or double-sided foam tape. Turn off the power and disconnect the video equipment. Determine the length of CAT-5 cable (up to 500 feet) needed to run between the source equipment and the remotely located equipment. Determine where the 846C power supply will be plugged in (will be connected to the HDTX unit). [. . . ]