User manual RYOBI 1500W TABLE SAW 254MM ETS1526AL

[. . . ] ETS-1526AL TABLE SAW OWNER'S OPERATION MANUAL N197 THANK YOU FOR BUYING A RYOBI TABLE SAW Your new table saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble free performance. CAUTION: Carefully read through this entire owner's manual before using your TABLE SAW. Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. [. . . ] Ensure that the yellow warning label is removed from the table before use. DESCRIPTION(FIG. Rear extension table LOOSE PART LIST A: Mitre gauge assembly B: Rip fence assembly C: Blade guard assembly D: Leg stand (4pcs) E: Cross Brace (4pcs) F: Push stick G: Blister pack with screws H: Extension table SPECIFICATION Input voltage Watts Blade diameter Bore size No load speed Depth of cut at 90° Depth of cut at 45° Main table size Rear extension table size Sound pressure level Net weight 240V ~ 50Hz 1500W 254mm 15. 9mm 4500min-1 80mm 55mm 720mm(W) x 520mm(L) 440mm(W) x 125mm(L) 99 dB(A) 23. 5 kg WARNING! Noise can be a health hazard. When the noise level exceeds 85 db (A) be sure to wear ear protection. PROPER USE OF MACHINE This machine is designed to rip and cross cut wood exclusively up to maximum thickness of 80mm. For correct operation it must be fixed and operated as explained in this manual. RESTRICTIONS OF USE DO NOT cut timber greater than 80mm DO NOT cut metal, stone, rubber, plastic bones, etc. DO NOT fit any other tool or combination of blades. DO NOT weld machine. Page 3 DO NOT modify the machine or its guards/ controls DO NOT run the machine before removing all packaging. DO NOT use with any covers/guards removed. DO NOT use High Speed Steel (HSS) blades. DO NOT use the saw for slotting (stopped groove). MOUNT THE ELEVATING AND LOWERING HANDLE AND THE TILTING HANDLE (FIG. 1) Mount the elevating handle(13) on the shaft on the left hand side of the saw and fix it by tightening the set screw in the handle (fig. 1). MOUNT THE BLADE (FIG. 1, 2&3) Remove the table insert(17) by removing the four Philips flat head screws. Turn the elevating handle(13) (Fig. 1) in the counterclockwise direction to raise the blade shaft to its highest position (fig. 3). Remove the blade fixing nut by turning in a counterclockwise direction, then pull the outer flange from the shaft and the outer arbor. Mount the blade(15) (be sure that the teeth are facing downwards at the front side of the saw). Replace the outer flange and refit the blade fixing bolt. Check that the blade is correctly seated before tightening the bolt. Check again that the blade(15) is securely tightened and re-fit or adjust riving knife as necessary, before re-mounting the table insert(17). WARNING! Replace table insert when worn. MOUNT THE RIVING KNIFE (FIG. 4&5) If in place, remove the table insert(17)by removing the four phillips flat head screws. Insert the riving knife(20), so that the long slots in the riving knife fit around the hexagon socket head end screws (Fig. 4). Adjust the riving knife(20) so that the clearance between riving knife(20) and blade(15) is between 2 to 5mm (Fig. 5); then tighten the hexagon socket headed screws. Check to ensure the riving knife(20) and saw blade(15) is in line. Then check again that the blade is securely tightened and remount the table insert. [. . . ] Align holes in the table saw base with holes in stand (Fig. Fully tighten all bolts to the stand before operation. WARNING! The stand consists of 4 holes for mounting to the ground. Always ensure your table saw with stand is securely mounted to the ground. If however, you have decided not to mount your table saw onto the stand, please refer to the 4 holes on the table saw and mount the unit to the workbench. [. . . ]