User manual RYOBI 18V ONE CIRCULAR SAW LCS180G

[. . . ] LCS-180 CORDLESS CIRCULAR SAW OWNER'S OPERATING MANUAL DESCRIPTION 1. Blade 10. Blade Screw 11. Outer Blade Washer 12. Inner Blade Washer 13. To Loosen 14. To Tighten 15. Battery Pack(Not Included) 16. Depress Latches to Remove Battery Pack 17. Guideline 18. Blade Guide Notch 19. Front of Saw 20. Straight Edge (Not Included) 21. Workpiece (Not included) 22. C-Clamp (Not Included) 23. Bevel Scale 24. Motor Housing 25. Lower Blade Guard Handle 26. Pocket Cut 27. 0º Bevel Stop 28. Hex Nut 29. Adjustment Screw 30. Carpenter's Square (Not Included) 1 2 7 3 6 4 5 8 7 9 12 Fig. 1 11 10 Fig. 2 16 15 13 15 10 8 14 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 1 2 3 Fig. 9 Fig. 10 Fig. 11 Fig. 16 23 6 18 5 Fig. 17 17 Fig. 18 24 23 18 6 Fig. 19 29 6 50 Fig. 20 9 25 28 27 30 26 Fig. 21 Fig. 22 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. English GENERAL POWER TOOL SAFETY WARNINGS 3. [. . . ] To reset the battery and tool, release the trigger and resume normal operation. NOTE: To prevent further shut down of the battery, avoid forcing the tool. Switching to a lower speed will also prevent shut down. If releasing the trigger does not reset the battery and tool, the battery pack is depleted. If depleted, the battery pack will begin charging when placed on the lithium-ion charger. NOTE: The battery pack is shipped in a low charge condition. Therefore, it must be charged prior to use. Refer to CHARGING BATTERY PACK for charging instructions. Align the raised rib on the battery pack with the groove inside the saw, then slide the battery pack into the saw. Make sure the latches on each side of your battery pack snap into place and the battery pack is secured in the saw before beginning operation. CAUTION When placing battery pack in the tool, be sure raised rib on battery pack aligns with the bottom of the tool and latches into place properly. Improper installation of the battery pack can cause damage to internal components. OPERATION WARNING Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING Always wear safety goggles or safety glasses with side shields when operating products. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. REMOVING THE BATTERY PACK(Not Included) See Figure 4. Locate the latches on the side of the battery pack and depress them to release the battery pack from the saw. WARNING Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. KICKBACK See Figures 5 - 8. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood. [. . . ] WARNING: To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. , come in contact with plastic parts. [. . . ]