User manual RYOBI 18V ONE COMPACT IMPACT DRILL LCDI1802G

[. . . ] 18 VOLT COMPACT HAMMER DRILL DRIVER OWNER'S OPERATING MANUAL LCDI1802 DESCRIPTION 1. Keyless chuck Torque adjustment ring Quick mode selector Two-speed gear train Rotation selector (forward/reverse/center lock) Depth rod stop Bit storage Trigger switch Mag TrayTM Handle screw Hex head hole Handle coller Teeth Depth stop rod clamp Auxiliary handle Battery pack (Not included) Latches Depress latches to release battery pack Reverse Forward Chuck jaws 22. Lock (tighten) Unlock (release) Low speed High speed Drive mode Drill mode Hammer mode To increase torque To decrease torque Bit Screws Bit holder Drilling depth Drill bit Scale To increase drilling depth To loosen To tighten To decrease drilling depth Chuck sleeve 1 2 3 4 6 8 5 9 7 Fig. 5 31 33 32 9 7 17 4 LO 24 25 18 HI 16 Fig. [. . . ] NOTE: Be sure the auxiliary handle is securely tightened against the depth stop rod clamp. This secures the depth stop rod at the desired depth of cut. WARNING Always wear safety goggles or safety glasses with side shields when operating products. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this product for the purposes listed below: Drilling in all types of wood products (lumber, plywood, panelling, composition board, and hard board) Drilling in ceramics, plastics, fiberglass, and laminates Drilling in metals Driving screws Hammer drilling in brick, or other masonry This product will accept RYOBI One+ 18 V lithium-ion battery packs and RYOBI One+ 18 V nickel-cadmium battery packs. BATTERy PROTECTION fEATURES RYOBI 18 V lithium-ion batteries are designed with features that protect the lithium-ion cells and maximise battery life. Under some operating conditions, these built-in features may cause the battery and the tool it is powering to act differently from nickel-cadmium batteries. During some applications, the battery electronics may signal the battery to shut down, and cause the tool to stop running. To reset the battery and tool, release the trigger and resume normal operation. NOTE: To prevent further shut down of the battery, avoid forcing the tool. If releasing the trigger does not reset the battery and tool, the battery pack is depleted. If depleted, the battery pack will begin charging when placed on the lithium-ion charger. Lock the trigger switch by placing the rotation selector in the center position. 3 SPECIfICATIONS Voltage Chuck Switch No load speed (Drill mode): -Lo speed -Hi speed Hammer speed (Blows per minute): -Lo speed -Hi speed Max. battery pack) MODEL BATTERy PACK (not included) BPL-1820 BPL-1815 BID1821 ABP1801 ABP-1815 18 V 2-13 mm Variable speed 0-400 min-1 0-1500 min-1 0-5200 min-1 0-19500 min-1 49 Nm 1. 68 Kg COMPATIBLE CHARGER (not included) BCL-1800 BCS618 BCL-1800 BCS618 ACR1800 260022029 OPERATION WARNING Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. English OPERATION Place the battery pack on the tool. Make sure the latches on each side of the battery pack snap into place and the battery pack is secured on the tool before beginning operation. WARNING Always remove battery pack from your tool when you are assembling parts, making adjustments, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury. Lock the trigger switch by placing the rotation selector in the center position. [. . . ] Depress the trigger switch to start the drill. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force the drill or apply side pressure to elongate a hole. Let the tool do the work. English OPERATION WARNING: Be prepared for binding at bit breakthrough. [. . . ]