User manual RYOBI 2000W HEAT GUN DUAL TEMP / VARIABLE HEAT EHG2002LED

[. . . ] Keep the work area clean and uncluttered. Keep children and visitors away from the work area, heat gun and any extension cables. To reduce the risk of electric shock, please wear proper shoes to avoid contact with earthed surfaces. Never carry the heat gun by its power cable or pull on the cord to disconnect it. [. . . ] This device shall connect to such power supply network which impedance equal to or less than 0. 063 + j0. 039 or the agreement of power supplier or user, any misconnection may cause high voltage fluctuation. WARNING: Always concentrate on the job and use common sense when working with this or any other tools. Do not use this tool when you are tired or taking medication that may make you drowsy. NB: Keep the nozzle at least 10 cm away from the working surface. Heat guns have a safety cut-off which will stop the heat gun if you are working too close to the surface being stripped. If the cut-off operates, the heat gun must be allowed to cool for about 30 minutes before it can be used again. page 2 RULES FOR SAFE OPERATION After use, remove any paint or varnish residue on the nozzle and scrappers. Never use the heat gun in combination with STRIPPING PAINT AND VARNISH solvents. Flakes and residues of lead-based paints are highly toxic. POWER SUPPLY Ensure that the power supply corresponds to the rating plate on the heat gun. The power supply should be 240V 50HzAC (normalmains). Voltage deviation greater than 10% may cause loss of power and possible overheat. For greater safety, the heat gun is double insulated. This means that there are two separate insulation systems between the user and the live elements of the heat gun. Warning: Although the heat gun is double insulated, normal safety precautions should be taken when using the heat gun to avoid injury that may be caused by a failure of the electrial installation inside the equipment. This tool is not designed to be earthed. The heat gun power cable is, therefore fitted with a two pin plug for use in normal 240V power sockets. SPECIFICATION Model No. : Rating: Voltage: Frequency: Temperature: Air flow: EHG2002LED 2000W 240V 50Hz o 50 C-650oC 250 to 500 l/min EHG2002 2000W 240V 50Hz o 60 C and 600oC 250 and 500 l/min Variable temperature adjust: LED temperature indicator: Yes Yes 2 Temperature No DESCRIPTION 1. Variable temperature control (For EHG2002LED only) 4. LED temperature indicator (For EHG2002LED only) USING THE HEAT GUN The heat gun is very easy to use. Before plugging the heat gun in, always ensure that the switch is set to 0. (OFF) When you are ready, adjust the switch (4) to setting 1 or 2. Always allow the heat gun to warm up for at least 1minute to reach the operating temperature. The heat gun has a built-in stand to keep it upright on a flat horizontal surface. This leaves both hands free for softening PVC pipes or other material. Always keep your hands away from the nozzle. If your heat gun model has a variable temperature control (3) you can rotate this to adjust to different temperatures. If your heat gun model has LED temperature indicator (6) (Fig. 4) then you can take a reference on the LED indicator to know what is the approximate working temperature. Pape 3 STRIPPING PAINT AND VARNISH The following procedure and techniques make it easier to strip paint and varnish. [. . . ] LTD. GUARANTEE Subject to the guarantee condition below, this Ryobi tool (hereinafter called "the product") is guaranteed by Ryobi (hereinafter called "the Company") to be free from defects in material or workmanship for a period of 24 months from the date of original purchase covering both parts and labour. Under the terms of this guarantee, the repair or replacement of any part shall be the opinion of the Company or its authorised agent. Should service become necessary during the warranty period, the owner should contact the RYOBI HELPLINE 1300 361 505 or contact the retailer from whom the product was purchased. In order to obtain guarantee service, the owner must present the sales docket and Guarantee Certificate to confirm date of purchase. [. . . ]