User manual RYOBI 310BVR-SERIALS-206058151-THRU-304122404

[. . . ] Es imprescindible que lea las instrucciones de este manual antes del montaje y de la puesta en servicio. Prima di procedere al montaggio e alla messa in funzione, indispensabile leggere attentamente le istruzioni del presente manuale. indispensvel ler as instrues deste manual antes de montar e pr em servio. Het is absoluut noodzakelijk vr montage en inbedrijfstelling de aanwijzingen in deze handleiding te lezen. [. . . ] Move the rip fence out of the way when cross cutting. Feed the work into the blade or cutter AGAINST the direction of rotation only. Never use the fence as a cut-off gauge when crosscutting. Never attempt to free a stalled blade without first turning the saw OFF. Turn off the power switch immediately to prevent motor damage. When transporting the machine use only transportation devices and do never use guards for handling or transportation. During transportation the upper part of the saw blade should be covered; for example by the guard. Use an extension table for supporting long workpieces during cutting operation. DESCRIPTION 1. Body ON/OFF Switch Rip Fence Lock Knob Extension Table Rip Fence Blade Guard Table Top Mitre Gauge Mitre Gauge Lock Tilting Handle Bevel Indicator Elevating Handle Reset Button Saw Blade Push Stick Table Insert Front Rail Sliding Block Riving Knife Stand (Optional) Dust Port s s s s s SPECIFICATIONS Input voltage Watts Blade diameter Bore size No load speed Depth of cut at 90 Depth of cut at 45 Main table size Extension table size Sound pressure level Net weight 110V / 230 V ~ 50 Hz 1500 W 254 mm 30 mm 4500 min-1 80 mm 50 mm 638 x 430 mm 638 x 260 mm 99 dB(A) 35. 5 kg s s s s s s s s WARNING Noise can be a health hazard. When the noise level exceeds 85 dB(A) be sure to wear ear protection. s PROPER USE OF MACHINE This machine is designed to rip and cross cut wood exclusively up to maximum thickness of 80 mm. For correct operation it must be fixed and operated as explained in this manual. s s 8 310BVR-SERIALS-206058151-THRU-304122404 manual 9/09/03 17:40 Page 9 F GB D E I P NL S DK N FIN GR H CZ RUS RO PL English RESTRICTIONS OF USE s s s s s s s s s s DO NOT cut timber greater than 80 mm DO NOT cut metal, stone, rubber, plastic bones, etc. Then mount the blade (15) (be sure that the teeth are facing the front side of the saw). Fix the blade in place by using the fixing nut. Check again that the blade is securely tighten and remount the table insert. WARNING Replace table insert when it was worn. ADJUSTMENT OF SAW BLADE WARNING Do not use saw blades which are damaged or deformed. Use only saw blades recommanded by the manufacturer. 15) Press the `ON' button to start the machine. Press the `OFF' button to stop the machine. WARNING Before turning the machine ON, make sure the blade guard is correctly installed and operating properly. MITRE CROSSCUTTING Mitre crosscutting is cutting the wood at an angle other than 90 with the edge of the wood (Fig. Follow the same procedures as you would for crosscutting. Adjust the saw blade to the desired angle. OVERLOAD RESET BUTTON (FIG. 15) Your Performance Power table saw features an overload reset button (14). [. . . ] La garanzia esclusa anche per gli accessori come batterie, lampadine, lame, punte, borse, ecc. In caso di malfunzionamento nel corso del periodo di garanzia, riportare il prodotto NON SMONTATO corredato della prova d'acquisto al fornitore o al pi vicino Centro di Assistenza Autorizzato Ryobi. II diritti legali relativi ai prodotti difettosi non sono rimessi in causa dalla presente garanzia. GB WARRANTY - STATEMENT P GARANTIA - CONDIES All Ryobi products are guaranteed against manufacturing defects and defective parts for a period of twenty four (24) months from the date stated on the original invoice drawn up by the retailer and given to the end user. Deterioration caused by normal wear and tear, unauthorised or improper use or maintenance, or overload are excluded from this guarantee as are accessories such as battery packs, light bulbs, blades, fittings, bags, etc. [. . . ]