User manual RYOBI 41AS310G034-41BS310G034

[. . . ] 3-4 Specific Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Rules for Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the power supply cord is damaged, it must be replaced only by the manufacturer or by an authorised service centre to avoid risk. SAFETY RULES FOR CHARGER WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery and product using battery to prevent misuse of the products and possible injury or damage. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. That extension cord is properly wired and in good electrical condition. That wire size is large enough for AC ampere rating of charger as specified below: Cord Length (Metre) Cord Size (AWG) 7 16 15 16 30 16 CAUTION: To reduce the risk of electric shock or damage to the charger and battery, charge only nickel-cadmium rechargeable batteries as specifically designated on your charger. Other types of batteries may burst, causing personal injury or damage. Do not use charger outdoors or expose to wet or damp conditions. 1. 6 mm Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Volt DC No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (RPM) Charger Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 V, 50 Hz, AC only Charge Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-90 min Pad Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125mm ON ( I ) / OFF ( O ) SWITCH HOOK-AND-LOOP SANDING DISCS Fig. 1 8 FEATURES KNOW YOUR SANDER See Figure 1. The safe use of this product requires an understanding of the information on the product and in this operator's manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. ORBITAL SANDING ACTION The oscillating action of your sander produces a very quick, small circular motion of the sanding pad. The motion is ideal for producing a fine finished grain. QUICK CHANGE HOOK-AND-LOOP PAD The hook-and-loop design allows for quick change of sanding sheets. It also enables you to easily clean and reuse them. ON/OFF SWITCH The ON ( I ) / OFF ( O ) switch is located on the front of the tool. ASSEMBLY UNPACKING This product has been shipped completely assembled. Carefully remove the product and any accessories from the box. [. . . ] Extended periods of sanding may overheat the motor. If this occurs, turn the sander off and wait until the sanding sheet comes to a complete stop. Remove sanding disc, then turn sander on and run it free without a load to cool the motor. 6 13 MAINTENANCE GENERAL MAINTENANCE WARNING: When servicing, use only identical replacement parts. [. . . ]