User manual RYOBI 4730301

[. . . ] OPERATOR'S MANUAL WIDE TABLE KIT 4730301 FOR USE WITH RYOBI BT3100 AND RYOBI BT3100-1 TABLE SAW WIDE TABLE KIT SHOWN ATTACHED TO BT3100/BT3100-1 TABLE SAW LUMBER NOT INCLUDED WITH THIS KIT TABLE SAW AND STAND NOT INCLUDED WITH THIS KIT Your new Wide Table Kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi accessory kit. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] FRONT EXTENSION RAIL T-NUT CONNECTOR WASHER TABLE BRACKET HEX BOLT TO ATTACH REAR EXTENSION RAIL See Figure 3 and 5. The rear extension rail attaches to rear rail on your BT3100/ BT3100-1 table saw by repeating the above procedure for attaching front extension rail. The only difference being the rear rail has a different configuration. NOTE: There are several repetitive steps required for assembling this kit. Please study and review illustrations closely for clarification when asked to repeat a procedure. After attaching rear rail extension to your saw you should now have the front and rear extension rails attached to your saw using four connectors, eight T-nuts, eight washers (5/16 in. ), and eight hex bolts (5/16 in. socket or the small wrench supplied with your table saw, tighten all eight bolts securely. Assure the two rail sets are straight before, during and after tightening. T-NUT CONNECTOR WASHER HEX BOLT FRONT RAILS SHOWN ATTACHED Fig. 2 REAR EXTENSION RAIL TABLE BRACKET SPACER REAR RAILS SHOWN ATTACHED Fig. 3 5 ASSEMBLY TO ATTACH TABLE BRACKETS Slide two T-nuts into channel on rear portion of front extension rail. Attach two table brackets and secure with washers (5/16 in. ) and hex bolts (5/16 in. Slide two T-nuts into channel on front portion of rear extension rail. Place a spacer between table brackets and T-nuts on rear extension rail as shown in figure 5. Secure table brackets and spacers with two washers (5/16 in. ) and two hex bolts (5/16 in. NOTE: These bolts are longer to accomodate spacers. Spacers are needed to provide clearance for the rip fence when sliding along extension rails. SPACER END CAP FRONT EXTENSION RAIL TABLE BRACKET T-NUT WASHER HEX BOLT Fig. 4 REAR EXTENSION RAIL AUXILIARY TABLE TOP (not supplied) We suggest you make the auxiliary table top from a piece of plywood cut 22 in. Space table brackets on each of the four corners so that they are approximately 6 in. Place table top in desired position on table brackets and adjust table brackets as needed. NOTE: End of table top closest to saw will rest on lip of accessory table. [. . . ] Construct them similar to methods explained for making table legs for auxiliary extension table. Either 2 x 4s or Ryobi Leg Set, # 4730305 can be used. A piece of 2 x 4 for securing table legs would need to be mounted on bottom of rear extension table. It should be located close to the end of rear extension table. [. . . ]