User manual RYOBI 495

[. . . ] OPERATOR'S MANUAL #4950300 ROUTER AND JIG SAW MOUNTING KIT (FOR USE WITH THE BT3000 TABLE SAW) CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT. Your new #4950300 Router and Jig Saw Mounting Kit has been designed for use with the RYOBI BT3000 Table Saw. It has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. This kit gives you the capability of mounting a router or jig saw on the accessory table of your BT3000. [. . . ] Place router upside down on a workbench and align mounting plate holes with tapped holes in the base of your router. The switch handle of router should be facing the squared end of mounting plate. Using the 8 mm flat head screws provided with your router, secure mounting plate to router. Once properly assembled, your router and mounting plate assembly should be similar to the illustration shown in figure 6. RE600 ELECTRONIC ROUTER 8 MILLIMETER SCREWS ROUTER MOUNTING PLATE FRONT OF ROUTER Fig. 5 TO ASSEMBLE MOUNTING PLATE WITH ROUTER ATTACHED TO ACCESSORY TABLE See Figure 7. 1. Place mounting plate under accessory table as shown in figure 7. Note: If desired you can remove accessory table, attach mounting plate with router, then reassemble complete assembly to your saw. Secure mounting plate to accessory table using the four #1/4-20 x 1/2 in. Tighten screws securely. INSTALLING ROUTER BIT Follow the instructions in the operator's manual of your router for this procedure. Install router bit and tighten securely in collet. 6 THROAT PLATE #1/4-20 SCREWS ACCESSORY TABLE CAUTION: Check to make sure it will not strike the accessory table or any metal surface. TO ASSEMBLE THROAT PLATE See Figure 7. Orient the throat plate as shown in figure 7, align tab with slot in accessory table, then place throat plate in recessed area of accessory table. Recheck router bit to make sure it will not strike the throat plate. SLOT TO ASSEMBLE TABLE CLAMPING BRACKET See Figure 8. The lever on the accessory table will tighten it securely to the front rail of your BT3000. However, the weight of your router and mounting plate, etc. may cause accessory table to be loose or have movement at the rear of the accessory table. To avoid this, install the table clamping bracket supplied with this kit. It can be used with a router mounted, with a jig saw mounted, or if desired it can be used with your BT3000 during normal use. Page 6 ROUTER WITH MOUNTING PLATE ATTACHED Fig. 7 ROUTER MOUNTING (Cont'd) TO ASSEMBLE TABLE CLAMPING BRACKET (Cont'd) 1. Remove end cap from rear rail as shown in figure 8. [. . . ] Round Hd. ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Knob Bolt (#5/16-18 x 1/2 in. ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Throat Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]