User manual RYOBI BD10R

[. . . ] 5 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If irritation is still present, see a doctor immediately. MIXING THE FUEL This product is powered by a 2-cycle engine and requires pre-mixing petrol and 2-cycle oil. Pre-mix unleaded petrol and 2-cycle engine oil in a clean container approved for petrol. This engine is certified to operate on unleaded petrol intended for motor vehicle use with an octane rating of 87 ([R + M] / 2) or higher. Do not use any type of pre-mixed petrol/oil from fuel service stations. This includes the pre-mixed petrol/oil intended for use in mopeds, motorcycles etc. Use a high quality 2-cycle self-mixing oil for air-cooled engines. Do not use motor vehicle oil or 2-cycle outboard oil. Mix the fuel thoroughly and also each time before refuelling. Do not mix quantities larger than usable in a 30 day period. If so, STOP THE ENGINE, and manually advance the string. 8 RUN POSITION HALF CHOKE POSITION CHOKE POSITION Fig. 9 CHOKE LEVER 10 MAINTENANCE WARNING: Use only original manufacturer's replacement parts, accessories and attachments. Failure to do so can cause possible injury, poor performance and may void your warranty. Make sure the string head and the spool retainer are installed on the drive shaft by turning the retainer anticlockwise to tighten. Pull the strings again to rotate the spool into cutting position. Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head. You may make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorised service dealer. Consequences of improper maintenance may include excess carbon deposits, resulting in loss of performance and discharge of black oily residue dripping from the silencer. Make sure all guards, straps, deflectors and handles are properly and securely attached to avoid the risk of personal injury. SPOOL RETAINER SPOOL REPLACEMENT EZ LINETM TAP ADVANCE SYSTEM NEW PRE-WOUND SPOOL See Figures 10 and 11. If replacing string only, refer to "String Replacement" later in this manual. [. . . ] Pull strings while alternately pressing down on and releasing spool retainer. Refer to "String Replacement" earlier in this manual. Advance string at full throttle. Engine starts but will only run at high speed at half choke: Carburettor requires adjustment. Engine does not reach full speed and emits excessive smoke: 1. Carburettor requires adjustment. Engine starts, runs, and accelerates but will not idle: String will not advance: Carburettor requires adjustment. 1. [. . . ]