User manual RYOBI BID1821M SCHEMA

[. . . ] 3 n Specific Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 n Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 n Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 n Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When working outdoors with a tool, use an extension cord that is designed for outside use. This type of cord is designated with "WA" on the cord's jacket. Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation. **Ampere rating (on tool data plate) WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool's internal insulation. Observe all normal safety precautions to avoid electrical shock. NOTE: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replacement parts when servicing. 0-2. 0 2. 1-3. 4 3. 5-5. 0 5. 1-7. 0 7. 1-12. 0 12. 1-16. 0 Cord Length 25´ 50´ 100´ 16 16 16 16 16 16 Wire Size (A. W. G. ) 16 16 14 16 14 12 14 14 10 14 12 -- ELECTRICAL CONNECTION This tool has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If your tool does not operate when plugged into an outlet, double-check the power supply. **Used on 12 gauge - 20 amp circuit. For correct operation of the unit, the tines must be installed in the correct orientation. n Lean the unit back on its wheels so that the handlebar rests on the ground. n Place tine C on the tine shaft to the left of the gear box. The stamped side of the tine should face away from the gear box. n Place tine B on the tine shaft to the right of the gear box. The stamped side of the tine should face away from the gear box. n Place a felt washer on each side of the tine shaft, and slide to rest against the inner tines. n Place the outer tine labeled D on the left side of the tine shaft. The stamped side should face in toward tine C. n Place the outer tine labeled A on the right side of the tine shaft. The stamped side should face in toward tine B. [. . . ] n Shift the drag bar up or down, depending on the depth you are trying to achieve. n Reinsert the pull pin through the wheel support and drag bar to secure. Fig. 14 14 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. [. . . ]