User manual RYOBI C356

[. . . ] 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 n Specific Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 n Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 n Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] wide, depending upon the thickness or width of the material and the setting at which the cut is being made. QUICK LOCK-RELEASE LEVER A quick lock-release lever has been provided on the cut-off machine. This feature allows you to open and close the vise clamp quickly without repetitive turning of the vise crank handle. 9 FEATURES VISE CLAMP A vise clamp has been provided with the cut-off machine. It is located on the end of the vise screw and provides greater control by clamping the material to the fence. It also prevents the material from creeping toward the wheel during a cutting operation. LOCK-ON BUTTON See Figure 3. The cut-off machine is equipped with a lock-on feature which is convenient when continuous cutting for extended periods of time is required. To engage the lock-on feature, depress switch trigger, push in and hold the lock-on button located on the side of the handle, then release switch trigger. Release lock-on button and machine will continue running. To release lock-on feature, depress switch trigger and release. If you have the lock-on feature engaged during use and the machine becomes disconnected from power supply, disengage the lock-on feature immediately. ADJUSTABLE FENCE The fence on the cut-off machine has been provided to support the material and provide clamping support to the vise for holding the material securely when making all cuts. It is an adjustable fence that has been provided to make the cut-off machine more versatile. n If any parts are damaged or missing, please call 1-800-525-2579 for assistance. WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury. WARNING: A 14 in. wheel is the maximum wheel capacity of your cut-off machine. Never use a wheel that is too thick to allow outer flange to engage with the flats on the spindle. Larger wheels will come in contact with the wheel guards, while thicker wheels will prevent the bolt from securing the wheel on the spindle. Either of these situations could result in a serious accident and can cause serious personal injury. WARNING: If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. 11 ASSEMBLY REMOVAL / INSTALLATION OF WHEEL TO REMOVE See Figure 5. n Push down on machine arm and remove transport chain from hook on motor housing to release machine arm. n Raise machine arm to its full raised position. Be cautious when raising, machine arm is spring loaded. [. . . ] Switch is damaged or burned out. SOLUTION 1. Have the cord replaced at your nearest authorized service center. Have the switch replaced at your nearest authorized service center and request a voltage check from the power company. Request a voltage check from the power company. [. . . ]