User manual RYOBI CCD1441 SCHEMA

[. . . ] 3-4 n Specific Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 n Safety Rules for Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 n Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 n Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Damage to the cord or charger could occur and create an electric shock hazard. n Make sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock. n Keep cord and charger from heat to prevent damage to housing or internal parts. n Do not let gasoline, oils, petroleum-based products, etc. They contain chemicals that can damage, weaken, or destroy plastic. NOTE: AWG = American Wire Gauge n Do not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman. n Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order. Take it to an authorized serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. Minimum 800 in. lb Blows Per Minute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000/BPM BUILT-IN COUPLER SWITCH TRIGGER FORWARD/ REVERSE SELECTOR WITH CENTER LOCK BIT STORAGE Fig. 1 KNOW YOUR IMPACT DRIVER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. FORWARD/REVERSE SELECTOR (DIRECTION OF ROTATION SELECTOR) The impact-driver has a forward/reverse selector located above the switch trigger. SWITCH LOCK BIT STORAGE The switch trigger can be locked in the OFF position. This feature helps reduce the possibility of accidental starting when not in use. When not in use, bits provided with the impact-driver can be placed in the storage area located on base of the handle. VARIABLE SPEED BLOWS PER MINUTE This tool has a variable speed switch that delivers higher speed with increased trigger pressure. Speed is controlled by the amount of switch trigger depression. This tool features an impact speed of 3, 000 Blows Per Minute (BPM). Blows Per Minute is the number of impacts per minute. SWITCH TRIGGER 8 The impact-driver has a conveniently located variable speed switch trigger. ASSEMBLY UNPACKING This product has been shipped completely assembled. n Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping. n Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. n If any parts are damaged or missing, please call 1-800-525-2579 for assistance. WARNING: If any parts are missing do not operate this tool until the missing parts are replaced. [. . . ] 6 13 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. [. . . ]