User manual RYOBI CDA1802M SCHEMA

[. . . ] do not use bits with a damaged shank Adjusting drilling depth 0 Holding and guiding the tool !@ - keep the ventilation slots uncovered - do not apply too much pressure on the tool; let the tool do the work for you SAFETY Read and save this instruction manual (pay special attention to the safety instructions at the back) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (UK 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug RYOBI can assure flawless functioning of the tool only when original accessories are used Before using accessories always compare the maximum allowed r. p. m. of that specific accessory with the r. p. m. of the tool This tool should not be used by people under the age of 16 years Be careful not to drill or drive into areas where electrical wires may be contacted The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always hold the tool firmly with both hands and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory APPLICATION ADVICE Use the appropriate bits # ! [. . . ] Inspect tool cords and plugs periodically and, if damaged, have them repaired by a qualified person. Inspect extension cords periodically and replace them, if damaged. Keep handles dry, clean and free from oil and grease. 16 Disconnect tools Disconnect tool when not in use, before servicing, or when changing accessories such as blades, bits and cutters. 17 Remove tool keys Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. 18 Avoid unintentional starting Do not carry a plugged-in tool with a finger on the switch. Be sure the switch is off when plugging in. 19 Outdoor use extension cords When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 20 Stay alert Watch what you are doing, use common sense and do not operate tool when you are tired. 21 Check damaged parts Before you use the tool, always carefully check the guarding and other parts to determine that they will operate properly and perform their intended functions. Check for alignment of moving parts, binding of moving parts and breakage of parts. 20 Soyez toujours attentif Observez votre travail, agissez en faisant de bon sens et n'employez pas l'outil lorsque vous tes fatigu. 21 Contrlez si votre outil est endommag Avant d'utiliser l'outil, vrifiez toujours soigneusement le parfait fonctionnement des dispositifs de scurit et des pices. Vrifiez si le fonctionnement des pices en mouvement est correct, si elles ne se grippent pas ou si d'autres pices sont endommages. Tous les composants doivent tre monts correctement et remplir les conditions pour garantir le fonctionnement impeccable de l'outil. Tout dispositif de scurit, tout interrupteur ou toute autre pice endommage ou dfectueusedoit tre rpare ou remplace de manire approprie par un technicien qualifi. N'utilisez aucun outil sur lequel l'interrupteur ne puisse ni ouvrir ni fermer le circuit correctement. Veillez utiliser l'outil et ses accessoires conformment aux instructions de scurit Veuillez galement tenir compte des possibilits de l'outil en prtant attention aux conditions de travail et la tche excuter. Utilisez l'outil pour des tches autres que celles prvues par l'outil, risquerait d'tre dangereux. 23 Faites rparr votre outil par un technicien qualifi Cet outil est conforme aux rgles de scurit en vigueur. Toutes les rparations doivent tre effectues par des professionnels qualifis avec des pices dtaches originales; faute de quoi l'utilisation de l'outil peut reprsenter un danger pour l'utilisateur. 26 GB CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: EN 50 144, EN 55 014, in accordance with the regulations 73/23/EEC, 89/336/EEC, 98/37/EEC. NOISE/VIBRATION Measured in accordance with EN 50 144 the sound pressure level of this tool is 96 dB(A), the sound power level 109 dB(A) and the vibration 14. 8 m/s2 (hand-arm method). [. . . ] STJ/VIBRATION Mles efter EN 50 144 er lydtrykniveau af dette vrktj 96 dB(A), lydeffektniveau 109 dB(A) og vibrationsniveauet 14, 8 m/s2 (hnd-arm metoden). CE SAMSVARSERKLRING Vi erklrer at det er under vrt ansvar at dette produkt er i samsvar med flgende standarder eller standard- dokumenter: EN 50 144, EN 55 014, i samsvar med reguleringer 73/23/EWG, 89/336/EWG, 98/37/EWG. STY/VIBRASJON Mlt iflge EN 50 144 er lydtrykknivet av dette verktyet 96 dB(A), lydstyrkenivet 109 dB(A) og vibrasjonsnivet 14, 8 m/s2 (hnd-arm metode). CE TODISTUS STANDARDINMUKAISUUDESTA Todistamme tten ja vastaamme yksin siit, ett tm tuote en allalueteltujen standardien ja standardoimisasiakirjojen vaatimusten mukainen EN 50 144, EN 55 014, seuraavien sntjen mukaisesti 73/23/EWG, 89/336/EWG, 98/37/EWG. [. . . ]