User manual RYOBI CDD1442 SCHEMA

[. . . ] Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service. Please fill out and return the Warranty Registration Card so we can be of future service to you. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE 15 22. 5 30 31. 62 45 TABLE OF CONTENTS Table of Contents and Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (10 mm) bolt holes have been provided in the saw base for this purpose. Each of the four mounting holes should be bolted securely using 3/8 in. (10 mm) machine bolts, lock washers, and hex nuts (not included). Bolts should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench. (457. 2 mm x 609. 6 mm) workbench is shown in Figure 11. Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to the floor before operating. WARNING: PADLOCK Always make sure your compound miter saw is securely mounted to a workbench or an approved workstand. Failure to do so could result in an accident resulting in possible serious personal injury. Fig. (12. 7 cm) DETENT STOPS ON MITER TABLE Detent stops have been provided at 0°, 22-1/2°, 30°, and 45°. The 22-1/2°, 30° and 45° detent stops have been provided on both the left and right side of the miter table. 18-5/8 in. 18" (47. 3 cm) 9-3/4" 8-5/8 in. Rotate the knob on the clamp to move it in or out as needed. R OT A 15 4 31. 62 30 22. 5 DUST GUIDE TION Fig. Remove battery pack from saw. 5 15 WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. 4 31. 62 45 31. 62 30 22. 5 15 30 22. 5 A dust bag is packed with your saw. It fits over the exhaust port on the upper blade guard. To install it, remove the dust guide from the exhaust port. Then, Page 15 WORK CLAMP KNOB Fig. 14 15 22. 5 30 45 ADJUSTMENTS TO INSTALL BLADE See Figures 15, 16, 17 and 18. LOWER BLADE GUARD BRACKET LOWER BLADE GUARD DANGER: A 8-1/4 in. (209. 6 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situations will result in a serious accident and can cause serious personal injury. Remove battery pack from saw. NOTCH PHILLIPS SCREW WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. [. . . ] Always use original factory replacement parts when servicing. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. They contain chemicals that can damage, weaken or destroy plastic and create a risk of serious personal injury. BATTERIES The battery pack for this saw is equipped with 15 nickel-cadmium rechargeable battery cells. Length of service from each charging will depend on the type of work you are doing. The battery cells have been designed to provide maximum trouble free life. [. . . ]