User manual RYOBI CDDI14022N SCHEMA

[. . . ] Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service. Please fill out and return the Warranty Registration Card so we can be of future service to you. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE 15 22. 5 30 31. 62 45 TABLE OF CONTENTS I I I I I I I I I I I I I Table of Contents and Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] While holding lock-off button pushed in, (2) depress switch trigger. Note: The spring loaded button will spring back into the lock-off position when the switch trigger is released. 0 15 UNLOCK LOCK-OFF BUTTON LOCK 1 2 3 30 22. 5 LOCK PIN 45 3 0 15 1 5 MITER TABLE CLAMP (IN LOCKED POSITION) 0 15 22. 5 30 31. 62 SWITCH 45 Fig. 9 FEATURES TRIGGER LOCK See Figure 10. To prevent unauthorized use of your compound miter saw, we suggest that you remove battery pack and lock the switch in the off position. To lock the switch, install a padlock through the hole in the switch trigger. When the lock is installed and locked, the switch is inoperable. Store the padlock key in another location. SWITCH TRIGGER Your compound miter saw should be permanently mounted to a firm supporting surface such as workbench. (10 mm) bolt holes have been provided in the saw base for this purpose. Each of the four mounting holes should be bolted securely using 3/8 in. (10 mm) machine bolts, lock washers, and hex nuts (not included). Bolts should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench. This will permit better air flow through the bag. DUST BAG METAL CLIPS DUST GUIDE See Figure 12. Remove battery pack from saw. WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. To install the dust guide, place the end marked INSERT over the exhaust port in the upper blade guard. Turn the guide so that the open end is facing down or toward the rear of the saw. EXHAUST PORT EXHAUST PORT R OT A TION Fig. 13 WORK CLAMP See Figure 14. Remove battery pack from saw. WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. To install work clamp, place the shaft of the clamp in either hole in front of the miter table base. Rotate the knob on the clamp to move it in or out as needed. R OT A 15 4 31. 62 30 22. 5 DUST GUIDE TION Fig. 12 DUST BAG See Figure 13. Remove battery pack from saw. 5 15 WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. 4 31. 62 45 31. 62 30 22. 5 15 30 22. 5 A dust bag is packed with your saw. It fits over the exhaust port on the upper blade guard. To install it, remove the dust guide from the exhaust port. [. . . ] Always use original factory replacement parts when servicing. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. They contain chemicals that can damage, weaken or destroy plastic and create a risk of serious personal injury. BATTERIES The battery pack for this saw is equipped with 15 nickel-cadmium rechargeable battery cells. Length of service from each charging will depend on the type of work you are doing. The battery cells have been designed to provide maximum trouble free life. [. . . ]