User manual RYOBI CR1201 SCHEMA

[. . . ] Vari-Orbit system is activated when saw blade enters into the workpiece Dust suction Prevents large accumulations of dust, high dust concentrations in the breathing air and facilitates the disposal of saw dust - mount vacuum cleaner adapter 5 - connect vacuum cleaner - clean vacuum cleaner adapter regularly !do not use vacuum cleaner when cutting metal Contact protector Contact protector G 2 prevents unintentional contact with the saw blade while working Changing blades 6 For mounting: - turn knob E counter-clockwise and hold it in this position - insert blade to full depth with teeth facing forward - release knob E For removing: - turn knob E counter-clockwise and hold it in this position - turn blade slightly to the right and pull it out - release knob E Adjusting bevel cutting angle 7 - loosen screw H - adjust footplate F to required angle - tighten screw H 5 q Operating the tool - before switching on the tool, ensure that front end of footplate rests flat on the workpiece - hold tool firmly with both hands, so you will have full control of the tool at all times - ensure that complete surface of footplate rests firmly on the workpiece - ensure that the blade has come to a complete standstill, before you lift the tool from the workpiece - keep the ventilation slots uncovered - use a stable support when cutting smaller or thin workpieces F INTRODUCTION q Cet outil est conu pour effectuer des dcoupes et coupes dans le bois, les matires plastiques, le mtal, les plaques en cramique et le caoutchouc, et est appropri pour des coupes droites et curvilignes avec des angles d'onglet jusqu' 45 SPECIFICATIONS TECHNIQUES 1 SECURITE q APPLICATION ADVICE q q q q q q q Use the appropriate saw blades 8 !Clic-system accepts T-shank blades 9 Splinter free cutting (plywood or similar material) 7 - set foot horizontal (splinter-free cutting is impossible in bevel-cutting position) - remove screw H - push foot forward, so that slot J covers blade on both sides - mount screw H Because of the strong heating that occurs when sawing metal, apply a cooling or lubricating product along the cutting line Plunge cutting 0 !to be used only on soft materials, such as wood, plaster boards, etc. [. . . ] Do not use power tools in damp or wet locations. Do not use power tools in presence of flammable liquids or gasses. 4 Guard against electric shock Avoid body contact with earthed surfaces (e. g. pipes, radiators, ranges, refrigerators). 5 Keep children away Do not let visitors contact tool or cord; they should be kept away from work area. 6 Store idle tools When not in use, tools should be stored in a dry and locked-up place, out of reach of children. 7 Do not force the tool It will do the job better and safer at the rate for which it was intended. 8 Use the right tool Do not force small tools or attachments to do the job of a heavy-duty tool. Do not use tools for purposes not intended (e. g. do not use a circular saw for cutting tree limbs or logs). 9 Dress properly Do not wear loose clothing or jewelry; they can be caught in moving parts. Do not use tool, if switch does not turn it on and off. Use the tool and its accessories in accordance with these safety instructions and in the manner intended for the particular tool, taking into account the working conditions and the work to be performed. Use of the tool for operations, different from those normally expected to be performed by the particular tool, could result in a hazardous situation. 23 Have the tool repaired by a qualified person This electric tool is in accordance with the relevant safety rules. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger for the user. Afin de rduire le risque de dcharge lectrique, de blessure et d'incendie lors de l'utilisation d'outils lectriques, observez les mesures de scurit fondamentales suivantes. Lisez et observez ces instructions avant d'utiliser l'outil. Conservez soigneusement ces instructions. 1 Vrifiez le voltage indiqu sur la plaque 2 Maintenez de l'ordre dans votre domaine de travail Le dsordre dans le domaine de travail augmente le risque d'accident. 3 Tenez compte de l'environnement du domaine de travail N'exposez pas les outils lectriques la pluie. N'utilisez pas d'outils lectriques dans un environnement humide ou mouill. Veillez ce que le domaine de travail soit bien clair. [. . . ] 10 Portez des lunettes de protection Utilisez aussi un masque si le travail excut produit de la poussire. 11 Installez le systme d'vacuation des poussires Si l'outil est quip des dispositives d'vacuation et de ramassage des poussires, assurez-vous qu'ils soient bien raccords et utiliss correctement. 12 Prservez le cble d'alimentation Ne portez pas l'outil par le cble, ne tirez pas sur le cble pour dbrancher la fiche de la prise, et prservez le cble de la chaleur, de l'huile et des artes vives. 13 Fixez bien la pice Employez un dispositif de serrage ou un tau afin de bien fixer la pice; elle sera ainsi bloque plus srement qu'avec votre main et vous aurez les deux mains libres pour manier l'outil. [. . . ]