User manual RYOBI CRP1801DM SCHEMA

[. . . ] It also includes a circle cutting jig for cutting circular patterns in both large and small stock. Properly cared for, it will provide years of dependable, trouble-free performance. RULES FOR SAFE OPERATION 1. READ THESE INSTRUCTIONS THOROUGHLY before assembling or using this router and jig saw mounting kit. READ THE INSTRUCTIONS FOR THE BT3000 TABLE SAW before operating your saw with this kit. [. . . ] Place spacer provided on threaded end of post. Thread post thru spacer into remaining 5/16 in. Tighten post securely with an adjustable wrench. Note: Adjustable wrench will fit flats on top of post. TO INSTALL DUST COVER AND PIVOT ASSEMBLY See Figure 4. 1. Place dust cover and pivot assembly on post as shown in figure 4. It will slide up and down post as needed. When desired location is achieved, secure it in place by tightening knob nut attached to carriage bolt. DUST COVER AND PIVOT ASSEMBLY CARRIAGE BOLT (NOT SHOWN) KNOB NUT FLATS ON POST POST KNOB BOLTS SPACER 5/16 in. WASHERS GUIDE FENCE BRACKET T-NUTS RIP FENCE Fig. 4 Page 5 ROUTER MOUNTING (Cont'd) TO ASSEMBLE RE600 ELECTRONIC ROUTER TO ROUTER MOUNTING PLATE See Figures 5 and 6. 1. Remove the subbase screws and subbase from your router. Figure 5 illustrates the correct orientation of parts and pieces for mounting your router to its mounting plate. Orient table clamping bracket as shown and secure with a 5/16 in. Note: Table clamping bracket fits in bottom slot of rear rail. The slotted top of this bracket wraps around the raised portion on the underside of the accessory table, clamping it tightly against the rear rail. TABLE CLAMPING BRACKET SHOWN COMPLETELY ASSEMBLED ACCESSORY TABLE TABLE CLAMPING BRACKET END CAP FINAL ASSEMBLY See Figure 9. After all router mounting parts have been assembled, your set-up should be similar to the illustration shown in figure 9. Compare your set-up to the set-up shown in figure 9 and make any necessary adjustments. Recheck all knob bolts, loose parts, etc. and securely tighten if necessary. PREPARING FOR OPERATION See Figure 9. Adjust dust cover so that it will not come in contact with workpiece during cutting operation. Direction of feed of workpiece is from right to left as shown by the arrow in figure 9. Direction of feed must always be so that the workpiece is being thrust against the sharp edges of rotating bit. [. . . ] 15 PILOT HOLE JIG SAW KIT SHOWN COMPLETELY ASSEMBLED Fig. 16 Page 11 #CRP1801DM0300 ROUTER AND JIG SAW MOUNTING KIT 5 3 4 5 3 4 2 1 12 3 4 11 6 7 8 10 9 13 14 15 19 20 23 25 24 22 21 Page 12 16 18 17 REPLACEMENT PARTS Now that you have purchased your Router and Jig Saw Mounting Kit, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center or other qualified service organization. Be sure to provide all pertinent facts when you call or visit. PARTS LIST KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 DESCRIPTION QUANTITY Guide Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Guide Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]