User manual RYOBI CRS1801 SCHEMA

[. . . ] Cluttered work areas and work benches invite accidents. DO NOT leave tools or pieces of wood on the saw while operating. The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. [. . . ] SYMBOL MEANING SAFETY ALERT SYMBOL: Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs. DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. NO HANDS: Failure to keep your hands away from the blade will result in serious personal injury. WET CONDITIONS ALERT: Do not expose to rain or use in damp locations. NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment. The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87. 1. SAVE THESE INSTRUCTIONS 2 UNPACKING INFORMATION Your miter clamping kit includes a miter clamp and the connecting hardware necessary to assemble and attach the miter clamp to the miter fence of your saw. NOTE: This kit applies downward and inward pressure to the workpiece. The kit snugly pulls the workpiece against the miter fence up to a maximum of 1/16 in. DO NOT TIGHTEN THE BOLT UNTIL THE WORKPIECE IS IN THE DESIRED POSITION AND YOU ARE READY TO SECURE THE MITER CLAMPER. Slide and turn the miter clamp on the post to activate the spring. The miter clamp is now spring loaded against the post and will remain in position when you release it. MITER FENCE Fig. 2 4 OPERATION PREPARING FOR CUTTING See Figure 3. Place the workpiece in the desired position against the saw's miter fence. Slide the miter clamp down against the workpiece as shown. As the knob bolt tightens, pressure against the post causes the miter clamp to pull the workpiece inward against the miter fence and down toward the table. As noted above, the miter clamp pulls the workpiece inward up to 1/16 in. TO RAISE MITER CLAMPING KIT INSTALLED POST TO LOOSEN KNOB BOLT TO LOWER TO TIGHTEN MITER CLAMP WARNING This clamping device provides assistance only; the operator must ensure control of the workpiece at all times. Failure to heed this warning could cause an accident resulting in serious personal injury. WORKPIECE MITER FENCE Fig. 3 5 NOTES 6 REPLACEMENT PARTS 4 2 3 5 3 6 4 1 8 7 PARTS LIST KEY NO. [. . . ] DESCRIPTION QUANTITY 1 2 3 4 5 6 7 8 Miter Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Wire Formed Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Phillips Pan Head Tapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]