User manual RYOBI CS1201 SCHEMA

[. . . ] 1) WORK AREA a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. [. . . ] If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 8 g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR JIG SAWS This tool should not be used by people under the age of 16 years WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Always keep the cord away from moving parts of the tool If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Do not cut material containing asbestos Do not use a saw blade which is cracked, deformed or dull Keep hands away from the saw blade while the tool is in use Remove all obstacles on top of as well as underneath the cutting path before you start cutting Always disconnect plug from power source before making any adjustment or changing any accessory Wear a dust protection mask when working with materials which produce dust that is detrimental to health; inform yourself beforehand about the materials to be worked on Wear protective goggles when working with materials which produce chips Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start cutting Check the functioning of the tool before each use and, in case of a defect, have it repaired immediately by a qualified person; never open the tool yourself Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) When used outdours, connect the tool via a fault current (FI) circuit breaker with a triggering current of 30 mA maximum, and only use an extension cord which is intended for outdour use and equipped with a splashproof coupling-socket The noise level when working can exceed 85 dB(A); wear ear protection When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill RYOBI can assure flawless functioning of the tool only when original accessories are used Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug On/off 3 Switch locking for continuous use 4 Changing saw blades 5 !insert blade to full depth with teeth facing forward 6 Sawing at 45 7 - for best results select "Normal" (4260) / "all" (CS1201) sawing mode !ensure that footplate rests flat against tool housing (7a or 7b) Adjusting sawing speed to material used 8 !Un cble endommag ou torsad augmente le risque d'un choc lectrique. e) Au cas o vous utiliseriez l'outil lectroportatif l'extrieur, utilisez une rallonge autorise homologue pour les applications extrieures. L'utilisation d'une rallonge lectrique homologue pour les applications extrieures rduit le risque d'un choc lectrique. 3) SECURITE DES PERSONNES a) Restez vigilant, surveillez ce que vous faites. Faites preuve de bon en utilisant l'outil lectroportatif. N'utilisez pas l'appareil lorsque vous tes fatigu ou aprs avoir consomm de l'alcool, des drogues ou avoir pris des mdicaments. Un moment d'inattention lors de l'utilisation de l'appareil peut entraner de graves blessures sur les personnes. GUARANTEE / ENVIRONMENT Always keep tool and cord clean (especially the ventilation slots) !CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 89/336/EG, 98/37/EG, 2002/96/EG. GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 80 dB(A) en het geluidsvermogen-niveau 91 dB(A) (standaard deviatie: 3 dB), en de vibratie 8, 1 m/s2 (hand-arm methode). CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 73/23/EG, 89/336/EG, 98/37/EG, 2002/96/EG. [. . . ] CE STANDARDIZASYON BEYANI Yeane sorumlu olarak, bu rnn aflaidaki standartlara veya standart belgelerine uygun olduunu beyan ederiz: EN 60 745, EN 55 014, ynetmelii hkmleri uyarinca 73/23/EC, 89/336/EC, 98/37/EC, 2002/96/EC. / GRLT/T<TREfiIM llen EN 60 745 gre ses basinci bu makinanin seviyesi 80 dB(A) ve al>flma s>ras>ndaki grlt 91 dB(A) (standart sapma: 3 dB), ve titreflim 8, 1 m/s2 (el-kol metodu). F D NL S DK N FIN E P I H CZ TR 05 RYOBI Europe B. V. Kloot 78 PL OWIADCZENIE ZGODNOCI CE Niniejszym owiadczamy ponoszc osobist odpowiedzialno, e produkt wykonany jest zgodnie z nastpujcymi normami i dokumentami normalizujcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 73/23/WE, 89/336/WE, 98/37/WE, 2002/96/WE. HAASU/WIBRACJE Pomiarw dokonano zgodnie z norm EN 60 745 cinienie akustyczne narzdzia wynosi 80 dB(A) za poziom mocy akustycznej 91 dB(A) (poziom odchylenie: 3 dB), za wibracje 8, 1 m/s2 (metoda do-rka). [. . . ]