User manual RYOBI EMM0001

[. . . ] OPERATOR'S MANUAL AIRgrip MultiTASKitTM EMM0001 Your product has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make sure that all items listed in the packing list are included. 3 OPERATION TURNING THE VACUUM BASE ON/OFF See Figure 4. Press the button located on the side of the vacuum base to turn it ON and OFF. Always wait for at least 5 seconds between stopping and restarting the unit. USING THE AIR-GRIPTM VACUUM BASE See Figures 5 - 6. Vacuum grip technology allows the unit to be attached to most smooth surfaces. NOTE: The multi-function base is not used when mounting by vacuum grip. n Place the unit on the surface you want it secured to and push against the surface slightly to engage the seal. n Continue to hold the unit against the surface while pressing the on/off button. n Release the unit when you hear a change in motor sound. n To release the vacuum seal, turn the power to the vacuum base off. For fast release, press the protrusion on the back of the unit. NOTE: Pulling the unit off the wall without releasing the vacuum could damage the tool. The grooves located in the vacuum base can be used to help hold a tape measure or chalk line when working unassisted. PUSH THE ON/OFF BUTTON TO TURN THE VACUUM BASE ON OR OFF Fig. 5 ROUGH-SURFACE ADAPTOR See Figure 7. By using the rough-surface adaptor, you can use the AIRgrip feature to position the unit on many non-smooth surfaces, including brick and painted cinder block. NOTE: The AIRgrip feature cannot be used with stucco or unpainted cinder block. n Position the rough-surface adaptor on the surface where you want to secure the vacuum base. NOTE: The dotted lines on the adaptor should be visible. n Place the unit against the adaptor on the dotted lines, and push in slightly to engage the seal. n Continue to hold the unit against the surface while pressing the on/off button. n Release the unit when you hear a change in motor sound. TAPE MEASURE GROOVES Fig. 7 9 OPERATION USING THE MULTI-FUNCTION BASE See Figures 8 - 9. [. . . ] n Check the batteries regularly to avoid deterioration. Remove the batteries from the vacuum base, laser attachment, and/or lighting attachment, if you will not be using them for an extended time. n Do not disassemble the laser level attachment. This could cause exposure to hazardous laser radiation. [. . . ]