User manual RYOBI ESS200RS

[. . . ] 1) WORK AREA a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. [. . . ] If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 5 f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug RYOBI can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Do not work materials containing asbestos (asbestos is considered carcinogenic) When sanding metal, sparks are generated; do not use dustbag/vacuum cleaner and keep other persons and combustible material from work area Do not touch the moving sanding disc Do not continue to use worn, torn or heavily clogged sanding discs Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/ chip extraction when connectable Always disconnect plug from power source before making any adjustment or changing any accessory 6 WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Backing pads - never run the tool without backing pad A !Maintenez le cble loign des sources de chaleur, des parties grasses, des bords tranchants ou des parties de l'appareil en rotation. Un cble endommag ou torsad augmente le risque d'un choc lectrique. e) Au cas o vous utiliseriez l'outil lectroportatif l'extrieur, utilisez une rallonge autorise homologue pour les applications extrieures. L'utilisation d'une rallonge lectrique homologue pour les applications extrieures rduit le risque d'un choc lectrique. 3) SECURITE DES PERSONNES a) Restez vigilant, surveillez ce que vous faites. Faites preuve de bon en utilisant l'outil lectroportatif. N'utilisez pas l'appareil lorsque vous tes fatigu ou aprs avoir consomm de l'alcool, des drogues ou avoir pris des mdicaments. Un moment d'inattention lors de l'utilisation de l'appareil peut entraner de graves blessures sur les personnes. APPLICATION ADVICE For determining the right grit table 6 can be used as reference !always test out first on a piece of scrap material Remove dust skirt D for sanding hard-to-reach places 7 For more tips see www. skileurope. com GUARANTEE / ENVIRONMENT Always keep tool and cord clean (especially the ventilation slots) - remove adhering sanding dust with a brush !disconnect the plug before cleaning This RYOBI product is guaranteed in accordance with statutory/country-specific regulations; damage due to normal wear and tear, overload or improper handling will be excluded from the guarantee In case of a complaint, send the tool undismantled together with proof of purchase to your dealer or the nearest RYOBI service station (addresses as well as the service diagram of the tool are listed on www. CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. [. . . ] CE STANDARDIZASYON BEYANI Yeane sorumlu olarak, bu rnn aflaidaki standartlara veya standart belgelerine uygun olduunu beyan ederiz: EN 60 745, EN 55 014, ynetmelii hkmleri uyarinca 73/23/EC, 89/336/EC, 98/37/EC. / GRLT/T<TREfiIM llen EN 60 745 gre ses basinci bu makinanin seviyesi 81 dB(A) ve al>flma s>ras>ndaki grlt 92 dB(A) (standart sapma: 3 dB), ve titreflim 3, 1 m/s2 (el-kol metodu). F D NL S DK N FIN E P I H CZ TR 05 RYOBI Europe B. V. Kloot 78 PL OWIADCZENIE ZGODNOCI CE Niniejszym owiadczamy ponoszc osobist odpowiedzialno, e produkt wykonany jest zgodnie z nastpujcymi normami i dokumentami normalizujcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 73/23/WE, 89/336/WE, 98/37/WE. HAASU/WIBRACJE Pomiarw dokonano zgodnie z norm EN 60 745 cinienie akustyczne narzdzia wynosi 81 dB(A) za poziom mocy akustycznej 92 dB(A) (poziom odchylenie: 3 dB), za wibracje 3, 1 m/s2 (metoda do-rka). [. . . ]