User manual RYOBI MM WS13-125SXEK

[. . . ] Teknik veriler, Güvenliğiniz için talimatlar, Kullanim, Şebeke bağlantisi, Bakim, Semboller Technická data, Speciální bezpečnostní upozornění, Oblast využití, Připojení na sít, Údržba, Symboly Technické údaje, Špeciálne bezpčènostné pokyny, Použitie podl’a predpisov, Siet’ová prípojka, Údrzba, Symboly Dane techniczne, Specjalne zalecenia dotyczące bezpiecze´nstwa, Użytkowanie zgodne z przeznaczeniem, Podłączenie do sieci, Gwarancja, Symbole Műszaki adatok, Különleges biztonsági tudnivalók, Rendeltetésszerű használat, Hálózati csatlakoztatás, Karbantartás, Szimbólumok Tehnični podatki, Specialni varnostni napotki, Uporaba v skladu z namembnostjo, Omrežni priključek, Vzdrževanje, Simboli Tehnički podaci, Specijalne sigurnosne upute, Propisna upotreba, Priključak na mrežu, Održavanje, Simboli Tehniskie dati, Speciālie drošības noteikumi, Noteikumiem atbilstošs izmantojums, Tīkla pieslēgums, Apkope, Simboli Techniniai duomenys, Ypatingos saugumo nuorodos, Naudojimas pagal paskirti, Elektros tinklo jungtis, Techninis aptarnavimas, Simboliai Tehnilised andmed, Spetsiaalsed turvajuhised, Kasutamine vastavalt otstarbele, Võrku ühendamine, Hooldus, Sümbolid Please read and save these instructions!WS 10-115 WS 10-125 WS 12-115 WS 12-125 WS 13-125 XE 1000 W 1000 W 1200 W 1200 W 1300 W 11500 min -1 11500 min -1 11500 min -1 11500 min -1 2800 - 11500 min -1 115 mm 125 mm 115 mm 125 mm 125 mm 22, 2 mm 22, 2 mm 22, 2 mm 22, 2 mm 22, 2 mm 1/3 mm 6 mm 115 mm 75 mm 1/3 mm 6 mm 125 mm 75 mm 1/3 mm 6 mm 115 mm 75 mm 1/3 mm 6 mm 125 mm 75 mm 1/3 mm 6 mm 125 mm 75 mm M 14 2, 4 kg 90, 1 dB (A) 101, 1 dB (A) GB Thread of work spindle M 14 M 14 M 14 M 14 Weight according EPTA-Procedure 01/2003 2, 3 kg 2, 3 kg 2, 4 kg 2, 4 kg Noise information Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are: Sound pressure level (Uncertainty K=3dB(A)) 87, 1 dB (A) 87, 1 dB (A) 87, 1 dB (A) 87, 1 dB (A) Sound power level (Uncertainty K=3dB(A)) 98, 1 dB (A) 98, 1 dB (A) 98, 1 dB (A) 98, 1 dB (A) Wear ear protectors!Vibration information Vibration total values (triaxial vector sum) determined according to EN 60745 Surface grinding: Vibration emission value ah, SG 6, 2 m/s2 6, 2 m/s2 6, 2 m/s2 6, 2 m/s2 2 2 2 Uncertainty K= 1, 5 m/s 1, 5 m/s 1, 5 m/s 1, 5 m/s2 Disk sanding: 6, 0 m/s2 6, 0 m/s2 6, 0 m/s2 6, 0 m/s2 Vibration emission value ah, DS Uncertainty K= 1, 5 m/s2 1, 5 m/s2 1, 5 m/s2 1, 5 m/s2 For other applications, e. [. . . ] B) Never place your hand near the rotating accessory. C) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging. D) Use special care when working corners, sharp edges etc. avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. E) Do not attach a saw chain woodcarving blade or toothed saw blade. such blades create frequent kickback and loss of control. Safety Warnings Specific for Grinding and Abrasive CuttingOff Operations: a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. B) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing. C) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. D) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges. E) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst. Additional Safety Warnings Specific for Abrasive Cutting-Off Operations: GB a) Do not “jam” the cut-off wheel or apply excessive pressure. Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. [. . . ] If needed, an exploded view of the tool can be ordered. As well as the machine type printed on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany. Please read the instructions carefully before starting the machine. Always wear goggles when using the machine. [. . . ]