User manual RYOBI P201

[. . . ] OPERATOR'S MANUAL 18 VOLT DRILL-DRIVER 2-SPEED P201 BATTERIES AND CHARGERS SOLD SEPARATELY Your drill-driver has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] n Red LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode. NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply. n If both yellow and green LEDs come on, this indicates a deeply discharged or defective battery pack. Allow the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack reaches normal voltage range, the red LED should come on. If the red LED does not come on after 30 minutes, this may indicate a defective battery pack and should be replaced. n After normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack. n The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. n Do not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature. NOTE: The charger and battery pack should be placed in a location where the temperature is more than 50°F but less than 100°F. n When batteries become fully charged, unplug the charger from power supply and remove the battery pack. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the purposes listed below: n Drilling in wood n Drilling in ceramics, plastics, fiberglass, and laminates n Drilling in metals n Mixing paint CAUTION: If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. Return the charger and battery to your nearest service center for service or replacement. LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK: n Red LED on = Fast charging mode. n Green LED on = Fully charged and in maintenance charge mode. n Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of normal temperature range. n Yellow and Green LEDs on = Deeply discharged or defective battery pack. n No LED on = Defective charger or battery pack. CHARGING THE BATTERY PACK Battery packs for this tool are shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the green LED on the front of the charger comes on. [. . . ] n Lock the switch trigger by placing the direction of rotation selector in center position. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. n Tap the hex key sharply with a mallet in a clockwise direction. This will loosen the screw in the chuck for easy removal. [. . . ]