User manual RYOBI P211

[. . . ] OPERATOR'S MANUAL 1/2 in. , 18 VOLT HAMMER DRILL 2-SPEED P211 BATTERIES AND CHARGERS SOLD SEPARATELY Your hammer drill has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] n Make sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only. n Connect the charger to the power supply. n Place the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger. n Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger. n Normally the red LED on charger will come on. This indicates the charger is in fast charging mode. n Red LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode. NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply. n If both yellow and green LEDs come on, this indicates a deeply discharged or defective battery pack. Allow the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack reaches normal voltage range, the red LED should come on. If the red LED does not come on after 30 minutes, this may indicate a defective battery pack and should be replaced. n After normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack. n The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. YELLOW LED RED LED Fig. 2 BATTERY PACK SHOWN IN CHARGER P110 CHARGER P100 BATTERY PACK Fig. 3 n Do not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature. NOTE: The charger and battery pack should be placed in a location where the temperature is more than 50°F but less than 100°F. n When batteries become fully charged, unplug the charger from power supply and remove the battery pack. 11 OPERATION CHARGING A HOT BATTERY PACK When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. [. . . ] n Lock the switch trigger by placing the direction of rotation selector in center position. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. n Tap the hex key sharply with a mallet in a clockwise direction. This will loosen the screw in the chuck for easy removal. [. . . ]