User manual RYOBI RCS3535A

[. . . ] 8 RCS3535A/2500/3500 PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SETUP LAN, WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PC NETWORK ADAPTER SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 BRING UP THE RCS3535A/2500/3500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fragment Threshold specifies the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the preset "RTS threshold" size, the RTS/CTS mechanism will not be enabled. The wireless router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The interval of time that this wireless router broadcast a beacon. Beacon is used to synchronize the wireless network. The range for the beacon period is between 20 and 1024 with a default value of 100 (milliseconds). The rate of data transmission should be set depending on the speed of your wireless network. Select the default mode of QoS from the list. IP Pred: In QoS, a three-bit field in the ToS byte of the IP header (see RFC 791). Using IP Precedence, a network administrator can assign values from 0(the default) to 7 to classify and prioritize types of traffic. 802. 1P: IEEE 802. 1p is a 3 bit field within an Ethernet frame header when using tagged frames on an 802. 1 network. It specifies a priority value of between 0 and 7 inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. This field is required if the source IP has been entered. The source port of the selected protocol. You cannot configure this field without entering the protocol first. The IP address of the traffic destination. This field is required if the Source IP Netmask (Source) Port (Source) Destination IP Netmask (Destination) Port (Destination) Protocol Physical Port ClassQueue 802. 1p_Mark IP. Pred_Mark TOS_Mark IP QoS Rules destination IP has been entered. The destination port of the selected protocol. [. . . ] If the current and new passwords are correctly entered, after you click `Apply', you'll be prompted to input your new password: Please use new password to enter web management interface again, and you should be able to login with new password. Time Zone The Time Zone allows your router to set its time; especially for recording System Log. Parameter Current Time Time Zone Select Enable SNTP client update SNTP server Description The current time of the specified time zone. You can set the current time by yourself or configured by SNTP server. Select the time zone of the country you are currently in. The router will set its time based on your selection. [. . . ]