User manual RYOBI RCS18352C

[. . . ] It is essential that you read the instructions in this manual before operating this machine. 11 English (Original instructions) Deutsch (Übersetzung der originalen Anleitungen) OPERATING INSTRUCTIONS Thank you for buying a Ryobi power tool. Each Ryobi power tool is carefully tested and subjected to strict quality controls by TTI quality assurance. Nevertheless, the service life of a power tool depends to a great extent on you. [. . . ] WARNING To avoid serious personal injury, do not attempt to use this product until you read thoroughly and completely understood the operator’s manual. Save this operator ’s manual and review frequently for safe operation and instructing others who may use this product. Cut from top (overbuck) avoid cutting earth Fig. 2nd cut overbuck (2/3 diameter) to meet 1st cut (to avoid pinching) Fig. 2nd cut overbuck (2/3 diameter) to meet 1st cut (to avoid pinching) Fig. Stand on uphill side when cutting because log may roll TECHNICAL DATA Unit Rated voltage Power rating Rated no-load speed Cutting length Chain brake Chain stop Chain oil tank capacity Weight (with guide bar, chain and empty tank) Emission sound pressure level LpA Uncertainty KpA Sound power level LWA Uncertainty KWA Guaranteed sound power level LWA(G) Vibration total value ah (no load work mode) Uncertainly K V~ / Hz W m/s mm s s ml kg dB(A) dB(A) dB(A) dB(A) dB(A) m/s2 m/s2 RCS1835 220~240/50 1800 13 350 < 0. 5 RHPDUNV WR WKH VSHFL¿FDWLRQV Ŷ The declared vibration value has been measured with a standard test method and may be used to compare one tool with another. Ŷ The declared vibration value may be used in a preliminary assessment of exposure. :DUQLQJ The actual vibration values during use of the tool can be different from the above stated and are depending on the use of the tool; and Of the need to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). 17 English (Original instructions) Deutsch (Übersetzung der originalen Anleitungen) CHAIN & BAR INFORMATION Model Chain Carlton N1C-BL-52E SK B Oregon 91PJ052X RCS1835 Oregon 91PJ052X Tri-link JL9d-3*52 Carlton N1C-BL-56E SK B RCS2040 Oregon 91PJ056X Tri-link JL9d-3 x 56 Note &KDLQ PXVW EH ¿WWHG ZLWK EDU DFFRUGLQJ WR DERYH FRPELQDWLRQV „ Carlton 14-10W-MHC UNB Y Tri-link DCR14B-050-3/8LP-52-B Carlton 16-10W-N156-MHC Oregon 160SDEA041 Tri-link DCR16C-050-Y56LD Bar Carlton 14-10W-MHC UNB Y Oregon 140SDEA041 SPECIAL PRODUCT FEATURES „ „ „ „ „ The product is using a special safety wrap-spring chain break mechanism to stop the chain within one tenth of a second if the chainbrake is engaged or the trigger is released. The saw chain’s safety drive links are designed to reduce the risk of kickback. In case of a “kickback, the chain brake is pushed forward” by the back of the operator’s hand and trips the quick brake of the chain saw. The lock-off Switch with lock to protect against unintentional start of the chain saw. The unique Ryobi Live tool indicator™ indicate the good connection with the power supply. Swing the chain tension adjust knob, turn the chain tensioning bolt clockwise until the saw chain is correctly tensioned. While the bolt is being tightened, the chain bar must then be pushed upwards, check chain tension again, do not tension the chain too tightly (Fig. 7) „ Replace the sprocket cover on top and tighten gently with the knob w/nut. 1RWH the saw chain is correctly tensioned if, in the middle of the cutter, it can be lifted 3mm to 4mm from the cutter upper edge. Starting the saw again with a new saw chain, allow it to run in for 2~3 minutes. :$51, 1* After the run-in time, check the chain tension and retighten the chain if necessary. Chain&Bar lubricant The chain saws are delivered without any oil in the oiltank. Prior to initial operation of the machine, the oil tank must be filled with lubricating oil. [. . . ] De faktiske vibrasjonsverdiene ved bruk av verktøyet kan skille seg fra dem som er oppgitt ovenfor, og er avhengig av hvordan verktøyet brukes; og behovet for å identifisere sikkeringstiltak som beskytter brukeren, basert på et anslag for eksponering i den faktiske brukssituasjonen (der man tar hensyn til alle brukssyklusene, som tidspunktet da maskinen ble slått av og når den går på tomgang i tillegg til tiden når verktøyet arbeider) Data om kjede og sverd Modell Utløser for gasshåndtak Carlton N1C-BL-52E SK B Oregon 91PJ052X RCS1835 Oregon 91PJ052X Tri-link JL9d-3*52 Carlton N1C-BL-56E SK B RCS2040 Oregon 91PJ056X Tri-link JL9d-3 x 56 +XVN Kjede må ha skinne påsatt som vist over. Kjede med sikkerhetsgripetenner for å minke faren for tilbakeslag. Hoveddeler er de følgende (kjede og sverd): Modell Utløser for gasshåndtak & Skinne Carlton Utløser for gasshåndtak N1C-BL-52E SK B & Carlton Skinne 14-10W-MHC UNB Y Oregon Utløser for gasshåndtak 91PJ052X & Oregon Skinne 140SDEA041 RCS1835 Oregon Utløser for gasshåndtak 91PJ052X & Carlton Skinne 14-10W-MHC UNB Y Tri-link Utløser for gasshåndtak JL9d-3 x 52 & Tri-link Skinne DCR14B-050-3/8LP-52-B Carlton Utløser for gasshåndtak N1C-BL-56E SK B & Carlton Skinne 16-10W-N156-MHC VEDLIKEHOLD (Fig. „ Tell antall stryk du bruker med filen på det første stedet for å bruke antallet som referanse for å file resten av kutterne med samme antall stryk. [. . . ]