User manual RYOBI SC155

[. . . ] 3-5 I Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 I Glossary of Terms and Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I Loose Parts and Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 I Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 I Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 I Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the scroll saw is to be used in a permanent application, we recommend that you secure it in a permanent location such as a workbench. When mounting the saw to a workbench, holes should be drilled through the supporting surface of the workbench. I Each hole in the base of the saw should be bolted securely using machine bolts, washers, and nuts (not included). Bolts should be of sufficient length to accommodate the saw base, washers, nuts, and the thickness of the workbench. Using the saw base as a pattern, locate and mark the holes where the scroll saw is to be mounted. I Drill four holes through the workbench. I Place scroll saw on workbench aligning holes in the saw base with the holes drilled in the workbench. I Insert all four bolts (not included) and tighten securely with washers and nuts (not included). Note: All bolts should be inserted from the top. Install the washers and nuts from the underside of the bench. Supporting surface where scroll saw is mounted should be examined carefully after mounting to insure that no movement during use can result. Adjust the sawdust blower/light to the desired position. Page 11 SMALL COMBINATION SQUARE E ORAG E ST BLAD TABLE LOCK KNOB Fig. 7 ADJUSTMENTS SETTING THE TABLE FOR HORIZONTAL OR BEVEL CUTTING See Figures 8, 9 and 10. HEX BOLT WARNING: Failure to turn the saw off and unplug the saw from the power source could result in accidental starting causing possible serious injury. A bevel scale is located under the saw table as a convenient guide for setting the approximate saw table angle for bevel cutting. When greater precision is required, make practice cuts on scrap material and adjust the saw table as necessary for your requirements. Note: When cutting at angles, the drop foot should be tilted so it is parallel to the saw table and rests flat against the workpiece. To tilt the drop foot, loosen phillips screw, tilt drop foot to the proper angle, then retighten screw. I Loosen the table lock knob and push down on the right side of the table. If the table stop at 0°, the zero degree stop is properly set. If the table stops somewhere other than zero, then adjust the zero degree stop. I To access the zero degree stop, loosen the table lock knob, and tilt the table with the right side all the way down. [. . . ] Remove the rubber cap from the upper and the lower arm of the saw. I Squirt a few drops of SAE20 oil around the shaft end and arm bearings. Let oil soak in overnight, remaining in this position. Note: Lubricate the bearings on the other side of the saw in this same manner. WARNING: If the power cord is worn, cut, or damaged in any way, have it replaced immediately by a qualified service technician. [. . . ]