User manual RYOBI TS1300

[. . . ] 3-6 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking and Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To lock the switch, install a padlock through the hole in the switch trigger. A lock with a long shackle up to 19/64 in. When the lock is installed and locked, the switch is inoperable. Store the padlock key in another location. 15 15 30 45 MITER LOCK HANDLE SAW ARM LOCKED IN DOWN POSITION SPINDLE LOCK BUTTON Fig. 3 POSITIVE STOPS ON MITER TABLE Positive stops have been provided at 0°, 15°, 22-1/2°, 30°, and 45°. The 15°, 22-1/2°, 30°, and 45° positive stops have been provided on both the left and right side of the miter table. SWITCH TRIGGER ELECTRIC BRAKE An electric brake has been provided to quickly stop blade rotation after the switch is released. FENCE The fence on your miter saw has been provided as a support to hold your workpiece securely against when making all cuts. SELF-RETRACTING LOWER BLADE GUARD The lower blade guard is made of shock-resistant, seethrough plastic that provides protection from each side of the blade. It retracts over the upper blade guard as the saw is lowered into the workpiece. 5 Page 9 FEATURES MOUNTING HOLE See Figure 6. Your miter saw should be mounted to a firm supporting surface such as workbench. Four bolt holes have been provided in the saw base for this purpose. Each of the four mounting holes should be bolted securely using 3/8 in. Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. 15 MITER TABLE 30 31. 62 45 TO TIGHTEN As mentioned previously your saw has been factory assembled and adjusted. The miter lock handle, dust guide or dust bag, table extensions, stop block, and blade are the only parts that have to be installed. 45 31. 62 30 22. 5 MITER LOCK HANDLE See Figure 7. To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threaded hole in the control arm under miter table. Turn clockwise to tighten. CONTROL ARM TO MITER LOCK HANDLE LOOSEN UPPER BLADE GUARD EXHAUST PORT Fig. To install the dust guide, place the end marked INSERT over the exhaust port in the upper blade guard. Turn the guide so that the open end is facing down. TO INSTALL BLADE See Figures 9, 10, and 11. WARNING: A 10 in. (254 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situations could result in a serious accident and can cause serious personal injury. 8 SCREW B WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. [. . . ] Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. Page 20 TROUBLESHOOTING PROBLEM Saw will not start. CAUSE 1. Have switch replaced by an Authorized Service Center. [. . . ]