User manual RYOBI TSC306 SCHEMA ELECTRIC

[. . . ] Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. connect this appliance to the power supply. Extension cords do not guarantee the required safety of the appliance (e. g. [. . . ] They must be 18 inches off the ground and protected by a barrier from vehicles. 9 Installation site Confined space installation ^ When installed in any space with less than 122 square feet, minimum clearances around the dryer must be adhered to for proper ventilation and vents for make up air must be installed. ^ Do not install any other fuel-burning appliance in the same space as the dryer. Confined door openings Any doors limiting circulation must be louvered or otherwise ventilated. A minimum of 200 square inches (1, 290 cm2) of opening is required. It must be equally divided within 12" (30. 5 cm) from the top and bottom of the door. Minimum installation clearance Sides: 0 " (0 cm) Top: 12" (30. 5 cm) Rear: 0" (0 cm) (as close to wall as gas connection and venting allows) Front to door: 2" (5 cm) Make sure the dryer door can open completely once installed. Exhaust duct clearance to combustible material: 2" (5 cm) 10 Installation Transporting the dryer to the installation site The rear of the lid has a handle for transportation. ^ Use the front dryer feet and the rear of the lid to move the dryer to the installation site. Level the dryer The dryer must be level to ensure safe and proper operation. ^ Unscrew the four feet as necessary by turning the foot, 1, and the locking ring, 2, to the left. ^ Once level, hold the foot, 1, still with a wrench. At the same time, turn the locking ring, 2, to the right using another wrench. , The dryer lid cannot be removed. 11 Installation , WARNING Before installation, disconnect the tumble dryer from the electrical supply by shutting off the power main or tripping the circuit breaker. Be sure the dryer power cord is unplugged from the wall. Maximum gas supply pressure before the gas pressure regulator 0. 37 psi (10" WC) for natural gas 0. 46 psi (13" WC) for LP gas. 14 Gas connection Gas supply Installation material (hoses and adapters) must be provided by the installer. Gas connection distances a Flare union adapter b 1/8" NPT pressure tapping plug c Gas shut-off valve For convenience (if allowed by code), an AGA or CGA approved flexible stainless steel gas hose (accordion type) may be used between the gas source and the dryer. This will allow the appliance to be moved from the installation site for cleaning or servicing. Make sure that nothing rubs on the gas hose. If there is any doubt concerning installation, contact the Miele Technical Service Department at the phone number listed on the back of this manual. This appliance must be installed with its own shut off valve on the gas supply line. (1. 8 m), and in the same room, of the dryer. An 1/8" NPT pressure tapping plug must be installed immediately upstream of the gas supply connection. This allows the gas inlet pressure to be checked. 15 Gas connection , To secure all connections use appropriate Teflon tape or a thread compound, suitable for gas connections. ^ Install a 3/8" flare union adapter, a, to the female elbow, b. Hold the elbow with a wrench. ^ At the end of the dryer's gas connection hand screw on the 3 /8" NPT elbow. Using a wrench tighten the elbow with a half turn. , DO NOT OVERTIGHTEN. ^ Secure the flexible metal gas line connector to the adapter. 16 Gas connection ^ Using two wrenches tighten the flexible gas line connection. ^ Using two wrenches tighten all connections. , DO NOT OVERTIGHTEN. ^ Connect the flare union adapter, a, to the pressure tapping plug, b, originally installed on the gas shut off valve, c. ^ Open the gas shut-off valve. ^ After connecting the appliance check all fittings for gas leaks e. g. [. . . ] ­ For best drying results avoid extra long ducting with too many bends, angles or tight corners. ­ The shorter the exhaust ductwork, the more efficient the dryer will be. Expelled air is slowed down in the ducts due to friction against the inner walls. It may result in poor drying results, damage to the laundry and higher Carbon monoxide emissions. The exhaust duct must not be connected or secured with screws or other fastening devices which extend into the interior of the duct. ^ Install the required connector*, 1, with the exhaust hose or pipe, 2, to the dryer. [. . . ]