User manual SAECO GROUP 700-ESPRESSO DOUBLE BOILER PLUS

[. . . ] Automatic beverage vending machine Saeco Group 700 NEW Model: ESPRESSO DOUBLE BOILER ESPRESSO DOUBLE BOILER PLUS SINGLE BOILER SINGLE BOILER PLUS TYPE: SG700N Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 OPERATION AND MAINTENANCE English MAIN PARTS 7 4 5 8 2 3 10 9 1 6 1 2 3 4 5 6 7 8 9 10 Brew group and coffee grinder Vending machine unit Sugar dispensing unit Electronic card Cup dispenser Coiner unit Tray socket Data plate Data plate showing the minimum and maximum water pressure Water mains connection 2 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English TABLE OF CONTENTS 11. 1 1. 2 1. 3 1. 4 77. 1 7. 2 PROGRAMMING. . . . . . . . . . . . . . . . . 27 Machine software updating through eprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Description of functions . . . . . . . . . . . . . . . . . . . . . . 31 INTRODUCTION TO THE MANUAL. . . . . . . . . . . . . . . . . . . . . . [. . . ] LOGICAL DATA That is all the data that refers to the logical statuses of the OPTION menu that describes the condition - enabled or disabled - of a specific function. The programming is carried out by using some key of the selection keypad (see fig. 47) and especially: 7 - PROGRAMMING With the programming procedures described in this section, it is possible to set all the parameters related to the machine configuration, the setting of the individual doses and beverage prices and also obtain sales statistical data. The 'dialogue' between the operator and the machine occurs by means of the 16-digit liquid crystal display and the use of the selection keyboard. Programming key The programming function is accessed by pressing button 1 located on the CPU board (fig. The request for the access code to be entered through the keypad (fig. 47) will be displayed. · decaffeinated preselection key or PRG exits from the current programming submenu to go back to the original submenu · key 1 or + has the double function of increasing the value of a selected figure - e. g. : the value of a dose and/or scrolling forward the list of functions available in the sub menu. 2 · key 2 or to decrease a value. This key decreases the value of a selected digit and/or scrolls backwards the list of functions of some submenus. · key 3 or Digit / Cancel through this key the display cursor moves to the digit to be modified through the above described + and - keys. In some menu, this key resets the parameters. · key 4 or Enter (also identified as E) to confirm the adjustments or to scroll and confirm the options menu 1 fig. 46 - during the installation the maintenance technician can select the language of the display messages, through the OPTIONS menu. NB: there are seven available languages stored on the eprom kit 'Language Dictionary', from which the language can be selected as mentioned above. Once parameter adjustment is completed, press button 1 on the CPU board (fig. 42) to exit the programming mode. Espresso Italia PTY LTD 27 www. espressoitalia. com. au Freecall 1300 660 976 English KEYPAD (fig. 47) The external keyboard besides being used for the selections is also partially used for programming and maintenance. In particular the keys and their functions are: Setting - 'Programming' mode Preselection key D Selection key 1 Selection key 2 Selection key 3 Selection key 4 PRESELECTION KEYS A B Sugar No Cup PRG (exit menu) + (increase/ forward scrolling) - (decrease/ backward scrolling) DIGIT / Delete (cursor position/ reset) ENTER (confirm) C Sugar D Decaffeinated KEYS Espresso 1 11 Espresso Long Espresso Espresso with Milk Cappuccino 2 12 LongEspresso 3 13 Espresso with Milk 4 14 Cappuccino Chocolate Cappuccino Coffee with hot chocolate Chocolate Coffee Milk 5 15 Chocolate Cappuccino Coffee with hot chocolate Chocolate Coffee Chocolate with Milk Hot Tea with Lemon 6 16 7 17 8 18 Milk with a dash of coffee Milk with Chocolate 9 19 10 20 Hot Peach Tea fig. 47 28 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English Maintenance - 'Service' mode Preselection key A Preselection key B Preselection key C Preselection key D Selection key 1 Selection key 2 Selection key 3 Selection key 4 Selection key 5 Selection key 6 Selection key 7 Selection key 8 Selection key 9 Selection key 10 Selection key 11 Selection key 12 Selection key 13 Selection key 14 Selection key 15 Selection key 16 Selection key 17 Selection key 18 Selection key 19 Selection key 20 test with water only complete test test without cup, sugar and stirrer failure reset brew group rotation / Yes milk-choc mixer washing / No lyo coffee mixer washing Instant product 1 mixer washing tea mixer washing ----nozzle arm movement --electronic counter reading machine initialisation boiler emptying --------------cup only dispensing (if the cup function has been programmed in the recipe key menu) Once the code is composed, press the key 'Enter' (4th) to access the programming mode. Important the default code is 00000 Once the code has been entered, the display shows the first main menu function: - press ENTER to select it - press + to go to the following function TIMES-DOSES Key 01 COFFEE PRICES Price DISCOUNTS Discount ex. a - press PRG to exit the job submenu. a) N. B. : while in the selection mode, the programming mode can be entered While in SERVICE mode, go first to the SELECTION mode through key 2 on the CPU board (fig. 60) and then to the PROGRAMMING mode, through key 1 (fig. 60). The main menu consists of: TIMES-DOSES DISCOUNTS KEY-RECIPE COINS TEMPERATURE DATA FOR MDB MDB TUBES UNLOADING PRICES PRICE-RECIPE OPTIONS SALES CLOCK MDB TUBES LOADING SAECO CARD Structure of job menus To access the programming it is necessary to know the access code or password. 00000 The access code consists of five digits. A cursor will appear under the first digit. Through keys + and - (the first and the second keys on the keypad) increase and decrease the number. With the 'digit' key, the third one, move the cursor. Repeat the operations until the access code is composed. Espresso Italia PTY LTD 29 www. espressoitalia. com. au Freecall 1300 660 976 English Press 'PRG' to exit the programming mode until one of the above mentioned functions appears on the display. Then press the programming key on the CPU board (key 1, fig. 42) to go back to the selection mode. The data related to the machine calibration and to the price, coins channel and machine settings can be stored in the SAECO ELECTRONIC KEY (fig. 48), thus using the same configuration for other machines of the same model. [. . . ] Disinfect all parts in contact with foodstuffs on a monthly basis using chlorine-based solutions, following the procedures already described in Chapter 4. 0. 9. 2. 2 Brew group maintenance - lower filter rod (1) - connecting rod (2) - guide rods (3) Every 10000 counts replace gaskets and filters: - gaskets Upper filter (fig. 61): fig. 61 - loosen the upper pin (1) using the supplied wrench - manually unscrew the filter (2) Lower filter: - unfasten the two side screws (ref. 1, fig. 62) and remove the upper piston lock (2) Plastic group. On a monthly basis remove the group and rinse it with plenty of hot water. [. . . ]