User manual SAECO SG200E

[. . . ] Hot beverage vending Machine Saeco Group 200 Model: ESPRESSO TYPE: SG200E i WARNING: This instruction manual is intended exclusively for specialized personnel. www. espressoitalia. com. au Espresso Italia PTY LTD Freecall 1300 660 976 OPERATION AND MAINTENANCE English MAIN PARTS 11 5 10 13 12 7 3 2 1 6 4 8 1 2 3 4 5 6 7 8 9 10 11 12 13 9 Brew group and coffee grinder Brewing hopper group Sugar and stirrer dispensing group CPU card Cup dispenser Payment system area POWER card Water circuit equipped with air-break device Pump Tray socket Data plate Data plate showing the minimum and maximum water pressure Water mains connection 2 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 77. 1 7. 2 TABLE OF CONTENTS PAYMENT SYSTEM INSTALLATION . . . . . . . . . . . . . . . . . . . . 24 Payment system installation on the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The responsibility for possible damages to the machine and other objects and for personal injuries caused by an incorrect installation of the payment system falls on the person who installed the system. - remove the cup dispenser - from the internal side of the door, cut the external film following the punched shape which corresponds to the desired cashless payment or coin validation system (fig. 36) fig. 37 - after finishing the whole perimeter, install and secure the payment system - connect the payment system to the CPU card - reassemble the cup dispenser NOTE: a special interface card is required for connecting 12 Vcd coins validation systems to the CPU card. - Then enter programming so as to choose convenient settings. See section 8 PROGRAMMING AND MAINTENANCE MENU in order to check parameter setting, which should be in line with the system used. fig. 36 - cut away plastic door joints by means of an hacksaw (fig. 37) 24 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 7. 2 Payment system installation on the base cabinet - connect the coiner to the CPU card NOTE: Executive, MDB and BDV serial systems are connected to the CPU card using a cable and an interface in necessary, both included in the special kit. - Then enter the programming menu so as to choose convenient settings. See section 8 PROGRAMMING AND MAINTENANCE MENU in order to check parameter setting, which should be in line with the system used. The base cabinet has no payment system. The responsibility for possible damages to the machine and other objects and for personal injuries caused by an incorrect installation of the payment system falls on the person who installed the system. - remove or turn the coiner supporting plate (fig. 38, ref. 1) - hook and secure the coiner to the support (fig. 38, ref. 2) - reassemble and lock the support to the cabinet door (fig. 38, ref. 3) fig. 38, rif. 1 fig. 38, rif. 2 fig. 38, rif. 3 fig. 38 Espresso Italia PTY LTD 25 www. espressoitalia. com. au Freecall 1300 660 976 English 8- PROGRAMMING AND MAINTENANCE MENU Important This chapter illustrates how to set up or modify the machine programming and maintenance parameters. It should therefore be read carefully, to fully understand the correct sequence of operations to be performed. 39 shows the standard position of keys on the door keypad; to which all the following sections will refer to. Key ò:DOWN Key ñ: UP Key c: CANCEL / beverage 01 Key e: ENTER / beverage 05 beverage 02 beverage 06 beverage 03 beverage 07 beverage 04 fig. 39 beverage 08 26 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 8. 1 Description of programming and maintenance phase keys 8. 2. 1 Entering the programming menu To surf inside the menu of the vending machine use the keys described below. 39) By pressing this key it is possible to access the following level of programming or maintenance. Furthermore it is possible to modify or confirm the values set in the entries of the programming or maintenance menus. 39) By pressing this key it is possible to go back to the previous level of the programming or maintenance menu. It is also possible to avoid storing the values of the previously required modification. 39) By pressing this key it is possible to access the preceding entry inside the same menu level. If used after requesting to modify a datum, it decreases its value of this same datum. 39) By pressing this key it is possible to access the following entry inside the same menu level. If used after requesting to modify a datum, it increases the value of this same datum. 8. 2 Programming menu The structure of the programming menu is shown in 8. 2. 2. 8. 2. 3 describes all the entries in the programming menu. Open the door, insert the key into the safety switch (fig. 18) and press key P1, located on the CPU card (fig. 40, ref. 1) so as to enter the programming menu. 1 2 3 fig. 40 If no password has been assigned you enter the programming menu directly. [. . . ] If this is not the case, stop and then restart the machine to allow the automatic positioning of the cup bracket. Remove the device by unhooking the elastic hook of the ring (fig. 60) Check the satellite scrolls and, if need be, rinse the device so as to remove dirt. fig. 61 In case of disassembly of all the internal parts of release ring assembly, refer to the specific assembling instructions (fig. 62) fig. 60 52 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English ALIGN THE FIVE SCROLLS REFERENCES ALIGN THE TWO ARROWS fig. 62 Espresso Italia PTY LTD 53 www. espressoitalia. com. au Freecall 1300 660 976 English 9. 5 Resin regeneration (where the water softener is provided) - remove the cover and introduce 1. 5 kg salt - refit the cover - turn the machine on and drain the water until it is no longer salty Resin regeneration is to be carried out according to the water of the system to which the dispenser is connected. Use the table below as a reference: WATER HARDNESS °French 10 20 30 40 50 SELECTION NUMBER 60cc 25000 12500 9500 6500 5000 130cc 12500 6000 4500 3000 2500 - power the machine off and close the tap. [. . . ]