User manual SAFEWAY TH-858C

[. . . ] € The electrical connection to the installation should be made via a socket with a plug with earth, or via an omnipole cut-out switch with an opening gap of at least 3 mm. € The yellow/green wire of the power supply cable must be connected to the earth of both power supply and appliance terminals. € Rosières cannot be held responsible for any accidents resulting from the use of an appliance which is not connected to earth, or with a faulty earth connection continuity. € Any queries regarding the power supply cord should be referred to After Sales Service or a qualified technician. [. . . ] The hob is supplied for a single phase connection : 220-240 V~ or two phase : 220-240 V2~. Remove the screws retaining the terminal block which contains the shunt bars and the conductors of the supply cord. Unscrew the cable clamp to release the power supplying cord. 2 - Operations to be carried out to make a new connection : . Choose the supply cord in accordance with the recommendations in the table on the next page. The hob must be in situation as shown : 16 . Strip the end of each conductor of the supply cord to a 10 mm length, by taking in account the requested length of the cord for the connection on the terminal block. According to the installation and with the help of shunt bars which you should have recovered in the first operation, fix the conductor as shown on the chart. Engage the earth wire yellow/green on the earth terminal, tighten the nut and verify the continuity of the earth. INSTALLATION: "ELECTRICAL CONNECTION" Connection of origin Single phase 220-240V~ FUSE C ABLE Type A e ra C onnection to the terminal block To shunt : make a bridge with a shunt bar Two phase 220-240V2~ 20A Three phase 220-240V3~ 20A Three phase 380-415 V3N~ 16A 20A H05RR-F H05RR-F H05RR-F H05VV-F 4 G 2, 5 mm² 1 2 3 4 5 H05RR-F H05VV-F 5 G 1, 5 mm² 1 2 3 4 5 3 G 2, 5 mm² 1 2 3 4 5 3 G 2, 5 mm² 1 2 3 4 5 E PH N PH PH E PH PH PH E PH PH PH N E 1rst Phase Shunt Shunt Neutral Shunt Earth 1rst Phase 1-2 Shunt 2-3 Shunt 2nd Phase 4-5 Shunt Earth 1rst Phase 1-2 Shunt 2-3 2nd Phase Shunt 4-5 3rd Phase Earth 1rst Phase 1-2 2nd Phase 3rd Phase 3-4 Neutral 5 Shunt Earth 1 2 3 4-5 IMPORTANT : Blue wire = Neutral Yellow/green wire = Earth For the connection to the terminal block, you must : . Do not forget to fix the earth wire (yellow/ green) on the earth terminal n° 6. When you become more familiar with the appliance, you will be able to choose settings to suit your own personal tastes and requirements. Slow cooking, sauces, stews, rice pudding, poached eggs . beans , frozen foods , fruit , boiling water . Steamed apples, fresh vegetables, pasta, crepes, fish . 21 For information, we note below the different powers reached according to the type of the plate and the control knob setting. E LE C TRIC AL HOT PLATE 7 po sitio ns Ø1 4 5 - 1 0 0 0 W fro nt right Ø1 8 0 - 1 5 0 0 W rear right Ø1 4 5 - 1 5 0 0 W rear left Ø1 8 0 - 2 0 0 0 W fro nt left POS ITION S 0 S T O P 1 100 135 135 175 2 165 220 165 220 3 250 300 250 300 4 500 850 500 850 5 750 1150 750 1150 6 1000 1500 1500 2000 Cooking with the electric hot plate To gest the best results from your appliance it is important to observe the following : • Use thick, flat-bottomed cooking vessels, a completely flat bottom prevents the overheating of some points which cause food to stick. Thick metal allows for good heat distribution. € Make sure that the bottoms of pans are dry : this will prevent things from sticking to the hot plate because of moisture. € Use pans with a diameter large enough to completely cover the hot plate, otherwise some of the energy will be wasted and if there are any spillages the hot plate will quickly become stained and difficult to maintain (rust, etc). € Never leave a hot plate switched on without a pan on it : it could become deformed, which would reduce its efficiency. € When cooking with fat or oil, do not remove the pan from the hob. [. . . ] Warning : during the hot plate is operating, it becomes hot, keep children away from it. 22 MAINTENANCE Before all cleaning or dismantling operation , it is imperative to : . Enamelled steel hob : simply clean the enamelled hob with soapy water when the hob is cold, rinse and wipe with a clean dry cloth. If you clean the enamelled hob when it is hot, you may tarnish it. [. . . ]