User manual SAGEM D50T

[. . . ] mars 2004 4:38 16 Livre du MD+. book Page i Mardi, 30. mars 2004 4:38 16 INTRODUCTION Dear customer: Thank you for purchasing a SAGEM DECT telephone; we appreciate your trust in us. This product was manufactured with the utmost care, should you encounter any difficulties during its use, we recommend that you refer to this user guide. You can also find information on the following site: http://www. sagem. com/faq For your comfort and safety, we ask that you read the following paragraph carefully: Recommendations and safety instructions Your DECT telephone must not be installed in a humid room (wash room, bathroom, laundry room, kitchen, etc. ) unless it is 1. 50 m away from a water point, or outside. [. . . ] Press Yes . - Room Monitoring Sender 2 Stop Both handsets are now in monitor mode. · Place the sender handset in the room to be monitored. The handset in sender mode does not ring to notify you of incoming calls. It can therefore be placed in a room where someone is sleeping. - Room Monitoring Mode Receiver Call Stop · Keep the receiver handset with you. When in monitor mode, the receiver handset can be used to make calls, dial the number or answer a call. At the end of the call, the handset will automatically return in monitor mode. To stop monitoring: - Press Stop R on the transmitter set. The receiver set will automatically return to the standby screen. - Press Stop Stop R R on the receiver set and confirm by pressing Yes and on the transmitter handset at the same time. 41 Livre du MD+. book Page 42 Mardi, 30. mars 2004 4:38 16 SECURITY SECURITY SECURITY Return Valid This menu enables you to change or customise the security parameters of your telephone. You can: · lock the keypad, · programme an emergency number, · modify the base code, · define the call time limit, · define forbidden prefixes, · authorise or deny communication to a number of handsets, · hide your telephone number. Locking/unlocking the keypad To lock/unlock the keypad, press and hold the keypad key some time. You can also lock your keypad via the SECURITY menu. On the navigator key , press or until the SECURITY screen is for displayed, press OK to confirm. KEYPAD LOCK Return KEYPAD LOCK?No Select KEYPAD LOCK using Valid or . . Press Valid . To lock the keypad, press Yes Yes KEYPAD LOCKED LONG PRESS ON * FOR UNLOCK A screen indicates that the keypad is locked. Programming an emergency number This function allows you to define an emergency number which can be enabled or disabled. Once it is activated, the emergency number will be automatically dialled when the green key · is pressed from the idle screen. Once activated, you can however call a different number with predialling by dialling a number and pressing The following types of numbers should not be programmed: Fire, emergency and police rescue services. . . 42 Livre du MD+. book Page 43 Mardi, 30. mars 2004 4:38 16 SECURITY On the navigator key , press or until the SECURITY screen is displayed, press OK to confirm. EMERGENCY Return Select EMERGENCY using Valid or . Press Valid . EMERGENCY OFF Valid Edit An information screen displays the current stored emergency number and indicates whether it is enabled or disabled. · · To keep the setting, press Valid To modify the setting, press Edit R . . A list of various executable actions appears: - ACTIVATE: to activate the emergency number. - DEACTIVATE: to deactivate the emergency number. - CHANGE NO: to modify the emergency number. CHANGE NO Return EMERGENCY NO: <Enter no> To modify the emergency number, select CHANGE NO. [. . . ] 3) Wear and tear from normal daily use of the Equipment and its accessories. 4) Communication problems related to an unsuitable environment, including in particular: · problems related to access to the telephone network such as interruptions by access networks or malfunction of the line used by the subscriber or his correspondent, poor line telephone quality, · transmission faults (for example, poor geographical coverage by radio transmitter line quality, or any interference between the environment and the radio transmitter), · modifications of parameters of telephone network carried out after the sale of the Equipment. 6) Work in connection with normal use: delivery, installation or exchange of consumable supplies, . . . 7) Work on any Equipment or software modified or added without the consent of SAGEM. [. . . ]