User manual SAGEM F@ST 1500-WG

[. . . ] SAGEM F@st 1500 TM SAGEM F@st 1500WG TM Reference Manual 288 053 220-03 August 2004 Issue S E closely follows all technological changes and is continually striving to improve its products for the benefit of its customers. It therefore reserves the right to change its documentation accordingly without notice. All the trade marks mentioned in this guide are registered by their respective owners: - SAGEM F@stTM is a registered trade mark of E. - Windows TM is a registered trade mark of Microsoft Corporation. - Internet Explorer is a registered trade mark of Microsoft Corporation. Warning Warning icon, used in this guide. ! Information icon, used in this guide. Contents Pages Contents 0-1 to 0-4 1. [. . . ] · LLC Point-to-Point Protocol over ATM Logical Link Control (LLC) allows multiple protocols running over one virtual circuit (using slightly more overhead). It is used in Best Effort for IP and Ethernet (for Data Application) Peak Cell Rate. Maximum Burst Size. QoS · CBR · VBR · UBR PCR/SCR/MBS · PCR · SCR · MBS SAGEM F@stTM 1500 Reference Manual - 288053220-03 Reproduction and communication prohibited without the written permission of E Page 4-15 4 - Configuring the SAGEM F@stTM 1500 ADSL router IP assigned by ISP Click Yes or No to assign or no IP address to your ISP IP Address Subnet Mask Connect Type IP address of the ATM interface. · Always connected · Auto - Triggered by traffic ·Manual - Start in Disconnected Your router is always connected to the WAN (automatic mode). Your router only connect to WAN when traffic is on (automatic mode). When your router start, this is disconnected to WAN (Manual mode). · Manual - Start in Disconnected When your router start, this is connected to WAN (Manual mode). · Manual - Start in Last State Idle Time (Minute) Username Password When your router start, this connect to WAN in last stated (Manual mode). Enter the maximum idle time for the Internet connection. After this time has been exceeded the connection will be terminated. In the field it appears the username that you entered during the SETUP WIZARD menu In the field it appears the Password that you entered during the SETUP WIZARD menu Confirm Password In the field it appears the Confirm Password that you entered during the SETUP WIZARD menu Confirm Password In the field it appears the Confirm Password that you entered during the SETUP WIZARD menu MTU Specifies the maximum size of the payload data in IP packets as a number of bytes (1500 in general) The following parameters only appear in "Routed" mode that you can select in the "Protocol" field: Default Gateway DHCP Client Default gateway of the ATM interface. Check this box if your ISP assigns an IP to clients using DHCP. SAGEM F@stTM 1500 Reference Manual - 288053220-03 Page 4-16 Reproduction and communication prohibited without the written permission of E 4 - Configuring the SAGEM F@stTM 1500 ADSL router 4. 4. 2 Clone MAC Some ISPs require you to register your MAC address with them. If this is the case, the MAC address of the SAGEM F@stTM 1500 ADSL Router must be changed to the MAC address that you have registered with your ISP. SAGEM F@stTM 1500 Reference Manual - 288053220-03 Reproduction and communication prohibited without the written permission of E Page 4-17 4 - Configuring the SAGEM F@stTM 1500 ADSL router 4. 5 LAN Use the LAN menu to configure the LAN IP address and to enable the DHCP server for dynamic client address allocation. Parameter LAN IP Description IP Address The IP address of the SAGEM F@stTM 1500 ADSL Router. IP Subnet Mask The subnet mask of the network. DHCP Server The SAGEM F@stTM 1500 ADSL Router comes with the DHCP function. To dynamically assign an IP address to client PCs, enable this function. For home networks this may be set to Forever, which means there is no time limit on the IP address lease. IP Address Pool Start IP Specify the start IP address of the DHCP pool. Do not include the gateway address of the SAGEM F@stTM 1500 ADSL Router in the client address pool. If you change the pool range, make sure the first three octets match the gateway's IP address, i. e. , 192. 168. 2. xxx End IP Specify the end IP address of the DHCP pool. Domain Name If your network uses a domain name, enter it here. Otherwise, leave this field blank. Remember to configure your client PCs for dynamic address allocation (See section 3. 1 for details). In this menu is included the following sub-menu: DNS (see section 4. 5. 1). SAGEM F@stTM 1500 Reference Manual - 288053220-03 Page 4-18 Reproduction and communication prohibited without the written permission of E 4 - Configuring the SAGEM F@stTM 1500 ADSL router 4. 5. 1 DNS Domain Name Servers (DNS) are used to map a domain name (e. g. , www. sagem. com) with the IP address (e. g. , 212. 234. 211. 50). Your ISP should provide the IP address of one or more Domain Name Servers. [. . . ] The following figure illustrates how the pins on an Ethernet RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. Figure C. 1 - RJ-45 Ethernet Connector Pin Numbers C. 1. 3 RJ-45 Port Connection Use the straight-through CAT-5 Ethernet cable provided in the package to connect the Sagem F@st1500 ADSL Router to your PC. When connecting to other network devices such as an Ethernet switch, use the cable type shown in the following table. Attached Device Port Type MDI-X MDI Connecting Cable Type Straight-through Crossover SAGEM F@stTM 1500 Reference Manual - 288053220-03 Page C-2 Reproduction and communication prohibited without the written permission of E Appendix C - Cable C. 1. 4 Pin Assignments General With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. [. . . ]