User manual SAGEM ITD 61

[. . . ] LU 252220355_ITD58-59-60-61-62-64-68-72_GB_V3 assemblé. fm Page 1 Mercredi, 20. juillet 2005 1:36 13 QUICK START CONGRATULATIONS! QUICK START Connection diagram ITD 60 and TV without scart DIGITAL TERRESTRIAL TV RECEIVER ITD 58 - ITD 59 - ITD 60 ITD 61 - ITD 62 - ITD 64 ITD 68* - ITD 72* *Top Up TV compatible This new generation of Set Top Box gives you access to new digital services and makes it easy for you and your family to choose the very best experiences of Digital TV. Once you have connected your Set Top Box and adjusted it according to your preference, you can enjoy all the services. You can update your Set Top Box through the antenna stream as new functions and services become available. [. . . ] Scroll through the choices using cursors or : 4-5 CHANNEL SEARCH IN PROGRESS This menu will be shown as the Set Top Box is searching for TV and radio channels. Please note that the search procedure may take a few minutes. You can cancel the search at any time by pressing EXIT. When the search procedure has ended, a message will indicate how many TV and radio channels have been found. · Press to finish the first time installation and to open the door of Digital TV. · TV format : 4/3 (Letterbox or Pan-scan) or 16/9. · TV RGB Output: low, medium, high or none if you want to have PAL video output (*). An indicator at the bottom of the screen will indicate the percentage of the scanned frequency band. The number of different services found is displayed in real time. INSTALLATION ENTER YOUR INSTALLATION CODE THEN PRESS OK TO CONFIRM ---- (*) Note that if you choose low, medium or high you will not able to choose the VCR standard format. 5-3-2 VCR (Not available on ITD58/59/60/68) Several choices are available. A message at the end of the scanning process will ask you to memorize. You can cancel the scanning process at any time by pressing the EXIT key. Scroll through the choices using cursor · PAL or S-Video standard. or : 4-6 AERIAL FAILURE If the channel search has found no channel, this screen is displayed to help you adjust the aerial. Enter a channel number (refer to http//www. dtg. org. uk/retailer/tx_details/_tx_index. htm. For example, Oxford channel numbers are 29, 34, 48, 51, 52, 68. These numbers depend on broadcasters and are subject to change. ) and move the antenna until the signal and quality bars are green. When signal and quality are green, press BACK to launch a new channel search. -6- An error message will be displayed if the code you have entered is not correct. MAIN MENU You can memorize or not. ENTER YOUR INSTALLATION CODE THEN PRESS OK TO CONFIRM **** BAD CODE PLEASE TRY AGAIN Note: You may observe a difference between the number of channel found and the number of channel present in the channel list. This may happen when you are in area where you receive same channel from different transmitters. -8- After a final check, press terminate. to memorize the settings. Press BACK to continue installation or EXIT to -7- -9- LU 252220355_ITD58-59-60-61-62-64-68-72_GB_V3 assemblé. fm Page 2 Mercredi, 20. BOX ADVANCED SETTINGS 5-3-3 Modulator (Only ITD60) If you want to adjust the channel for another TV set: · directly access the menu, · choose the channel (21 to 69) by entering the number, · choose the standard of your country (B/G, I or K). USER SETTINGS 6-1 LANGUAGE SETTING Go to main MENU/INSTALLATION/USER SETTINGS Press for access to various configurations. Select LANGUAGE SETTING and press to confirm. 6. USER SETTINGS 6-3 FAVOURITE LISTS INSTALLATION (not available on ITD 58/59/60/68) To go main MENU/INSTALLATION/USER SETTINGS/FAVOURITE LISTS This function will enable you to make up a FAVOURITE list of the TV or radio type from the reference list All Services. 6. USER SETTINGS 6-4 LOCKING (not available on ITD 58/59/60/68) To go main MENU/INSTALLATION/USER SETTINGS/LOCKING 6-3-1 CREATION · MENU LANGUAGE You may select the menu displayed languages. [. . . ] ENVIRONMENT Preservation of the environment is an essential concern of Sagem Communication. The desire of Sagem Communication to operate systems observing the environment and consequently it has decided to integrate environmental performances in the life cycle of its products, from manufacturing to commissioning, use and elimination. Error Code 1, 2 or 3 flashes Origin of Error Reception error User Action Acknowledge the message by pressing any key on the remote control. Acknowledge the message by pressing any key on the remote control. Acknowledge the message by pressing any key on the remote control. [. . . ]