User manual SAGEM MDP 2000 X

[. . . ] Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please contact your local reseller or service center. When the "TEMP" indicator lights solid red for about 20 seconds, it indicates the projector has been overheated. You will see a message "Projector Overheated. Lamp will automatically turn off soon. " on the on-screen display. The projector will automatically shut itself down. Under normal conditions, the projector can be switched on again after it has cooled down. If the problem persists, you should contact your local dealer or our service center. When the "TEMP" indicator flashs red for about 10 seconds, you will see a message "Fan fail. 14 This graph is for user's reference only. User Controls Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Control Panel Remote Control Using the Control Panel Power/Standby 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Source 4 Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources. Menu 4 Press "Menu" to launch the on screen display (OSD) menu. To exit OSD, press "Menu" again. Keystone /Keystone 4 Adjusts image distortion caused by tilting the projector (±16 degrees). Four Directional Select Keys 4 Use Enter your selection. to select items or make adjustments to 4 Confirm your selection of items. Auto Image 4 Automatically synchronizes the projector to the input source. English User Controls Using the Remote Control Power/Standby 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Re-Sync 4 Automatically synchronizes the projector to the input source. Volume + / - (Vol+/Vol-) Reset 4 Increases/decreases speaker volume. 4 Changes the adjustments and settings to the factory default value. Hide 4 Press "Hide" to hide image, press again to restore display of the image. Keystone / 4 Adjusts image distortion caused by tilting the projector (±16 degrees). Page Up (Computer mode only) 4 Use this button to page up. This function is only available Page Down (Computer mode only) when the projector is connected to a computer via an USB cable. 4 Use this button to page down. This function is only available Freeze when the projector is connected to a computer via an USB cable. 4 Press "Freeze" to pause the screen image. Four Directional Select Keys 4 Use Menu your selection. to select items or make adjustments to 4 Press "Menu" to launch the on screen display menu. To exit OSD, press "Menu" again. Enter 4 Confirm your selection of items. VGA 4 Press "VGA" to choose Analog RGB, component and HDTV source. S-Video 4 Press "S-Video" to choose S-Video source. English . . . 16 User Controls Composite 4 Press "composite" to choose Composite video source. DVI-D 4 Press "DVI-D" to choose DVI-D connector. 17 . . . English User Controls On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or Control Panel. 2. When OSD is displayed, use "Enter " key to enter sub menu. keys to select any item in the main menu. While making a selection on a particular page, press 3. Use settings by keys to select the desired item and adjust the key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. [. . . ] See page 27. Problem: Lamp burns out or makes a popping sound 4 When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp". See page 34. Problem: LED lighting message Message Standby State (Input power cord) Lamp lighting Power on Power off (Cooling) Error (Lamp fail) Error (Thermal fail) Error (Fan fail) Error (Over Temp. ) Error (Lamp Breakdown) Flashing Power LED Green Flashing Temp LED Lamp LED English . . . [. . . ]