User manual SAGEM MF 9535/MF 9545

[. . . ] MF9500 Operation Manual for Copier 30000113480-01 S INTRODUCTION This manual describes only copier features. For operation procedures relating to both the basic printer and copier features, refer to the "Operation manual (for printer operation and general information)". General information required for loading paper, adding toner, misfeed removal, and operation of peripheral devices are described in that manual. Separate manuals are provided for the operation of network scanning and facsimile functions. [. . . ] Automatic selection can be used only for 11" x 17", 81/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2" size originals and copy paper in the inch system and A3, B4, A4, A4R or A5 in the AB system. other desired such as 4 Make all or the number ofsettingsand press exposure copies, the [START] key. When copying from the document glass in the sort mode, touch the [READEND] key after all originals have been scanned. (step 7 on page 13) 2 Touch the [PAPER SELECT] key and then select the desired paper size. 1. A3 When the desired paper size key is touched, the paper size will be highlighted and the paper size setting window will be closed. If paper of the desired size is not loaded in any tray, load paper of the required size in a paper tray and enter the paper size. To cancel the auto image mode, touch the [AUTO IMAGE] key again to clear the highlighted display. IMAGE] 3 Touch the [AUTO82 1 key. AUTO PAPER SELEC AUTO IMAGE COPY RATIO The [AUTO IMAGE] key will be highlighted and the best reduction or enlargement ratio for the original size and the selected paper size will be selected and displayed in the copy ratio display. NOTE If the message "ROTATE ORIGINAL FROM TO " is displayed, change the orientation of the original as indicated in the message. When the message above is displayed, copying can be done without changing the orientation, but the image will not fit the paper correctly. 16 REDUCTION/ENLARGEMENT/ZOOM Manual selection the original in the document 1 Place the document glass. (page 7) feeder tray or on NOTE When the document feeder is being used, the available copy ratio range is 25% to 200%. other desired such as 5 Make all or the number ofsettingsand press exposure copies the [START] key. When copying from the document glass in the sort mode, touch the [READEND] key after all originals have been scanned. (step 7 on page 13) 2 Touch the [COPY RATIO] key. 100% COPY RATIO The preset copy ratio keys for reduction and enlargement, the keys for [ZOOM] and the [100%] key will be displayed. the copy ratio by touching a 3 Selectratio desiredreduction or enlargementfixed copy key for and touch the [OK] key. Use the and make fine adjustments as needed. keys to 100 25% ZOOM % OK 400% 10 B4 A3 B5 B4 B5 70% B5 A5 81% A4 A3 B4 A4 A4 A4 115% A5 B5 122% B5 A3 A4 A4 B4 B5 86% B4 B4 141% A3 AUT IMAG If the message "IMAGE IS LARGER THAN THE COPY PAPER. " appears, image loss will occur. In this case either continue with image loss or change the copy paper size or copy ratio. size 4 Ensure that the desired paperon thehas been automatically selected based selected copy ratio or select another size as needed. PAPER SELECT 86% COPY RATIO If another size paper is selected, the auto paper select display will be cleared. 17 SPECIAL PAPERS If a bypass tray and a duplex module, a duplex module/bypass tray or a multi purpose drawer*1 is installed, special papers can be fed. These include transparency film, postcards, labels, envelopes*2, and plain paper. *1 The upper tray of a stand/3 x 500 sheet paper drawer or a stand/MPD & 2000 sheet paper drawer is equivalent to the multi purpose drawer. *2 Envelopes can be set in the multi purpose drawer and in the upper tray of a stand/paper drawer. the original in the document 1 Place the document glass. (page 7) feeder tray or on special 2 Load the purposepaper in the bypass tray or in the multi drawer. For the paper loading instructions see "Loading paper in the bypass tray" (page 5-3) of the "Operation manual (for printer operation and general information)" or "Loading paper in the multi purpose drawer" (page 121) of the "Operation manual (for printer operation and general information)". 3 Touch the [PAPER SELECT] key and then select the bypass tray or the multi purpose drawer. 1. A4 COLOR 2. When loading paper in the A4 COLOR 2. paper type can be set by touching the [PAPER TYPE] bypass tray, the desired 3. 4. other desired such as 4 Make all or the number ofsettingsand press exposure copies, the [START] key. When copying from the document glass in the sort mode, touch the [READEND] key after all originals have been scanned. (step 7 on page 13) 18 SPECIAL MODE When the [SPECIAL MODES] key on the basic screen of the copy mode is touched, the special modes screen containing six special function touch keys will appear. These functions are shown below. SPECIAL MODES MARGIN SHIFT PAMPHLET COPY ERASE JOB BUILD DUAL PAGE COPY MULTI SHOT OK Margin shift: page 20 Erase: page 21 Dual page copy: page 22 Pamphlet copy: page 23 Job build: page 24 Multi shot: page 25 When using the multi shot function, set the original, select the desired paper, and select one-sided or two-sided copying before selecting the multi shot function on the special modes screen. [OK] key on the special modes screen Touch the [OK] key, to return to the basic screen of the copy mode. Common operation procedure for using the special functions 1 Touch the [SPECIAL MODES] key. SPECIAL MODES 2-SIDED COPY 2 Touch the key for the desired special mode. MARGIN SHIFT PAMPHLET COPY Example: To set the margin shift function: Setting procedures for modes requiring setting screens start on the next page. [. . . ] One-sided scanning from the document glass. Original feed system Automatic continuous feeding Original exit system Face down output Original transport system DSPF and SPF: sheet through type (reference position: center), document glass: reference position is left rear Original setting direction Face down Original sizes 5-1/2" x 8-1/2" to 11" x 17" or A5 to A3 Original weight 14 to 34 lbs. or 50 to 128 g/m2 Capacity Up to 50 sheets (30 sheets*1 for 8-1/2" x 14" or B4 or larger originals) provided the total aggregate thickness does not exceed 1/4" or 6. 5 mm (14 to 20 lbs. or 50 to 80 g/m2) or 3/16" or 5 mm (21 to 34 lbs. [. . . ]