User manual SAMMY MIGHTY DRIVER

[. . . ] Your game is assembled and should not need any assembly. Level your game using enclosed Leg levelers. and Canada 120V / 125V - 3A; Europe 220V / 240V - 2A. [. . . ] Payout after game over. -8 81 82 oo 91 92 oo A1 A2 A3 A4 A5 A6 A7 A8 A9 AA Ab AC Ad AE AF oo b1 b2 b3 b4 b5 b6 b7 b8 b9 bA bb oo C1 C2 C3 C4 C5 oo D1 E4 01 oo -9 TICKET PAYOUT SETTING -A SCORE SETTING PER 1 TICKET PAYOUT -b MERCY TICKET Payout when game is over. -C EXTEND GAME PLAY SETTING Not used when Ticket & Card payout is active. Used when player gets 30 flags -D -E -0 Do not use Do not use RESET "FACTORY INSTALLED" SETTING 6 TEST MODE You can check 3 tests in this mode. HOW TO ENTER THE TEST MODE Re-power on while pressing and holding the SERVICE Switch which is located inside of front door. Then release the SERVICE switch OFF to show the 1­ on 2 digits LED display on Marquee box. HOW TO SELECT AND DECIDE CONTENTS After entering TEST MODE, press SERVICE switch to move the number of contents. (2 digits will be changed by pressing the SERVICE switch. ) Press RESET switch to select it. After selecting, display shows each function numbers. TEST MENU FUNCTION NUMBER I/O & DISPLAY TEST MECHANISM TEST SOUND TEST >>> Display shows 1­ >>> Display shows 2­ >>> Display shows 3­ RETURN TO PREVIOUS MENU Each test function has the number "oo", select this and press RESET switch. If you want to quit the test during testing, press RESET switch when the LED Display does not show any numbers. I/O & DISPLAY TEST Display shows 1­ then press SERVICE switch to select following TEST menu. (11, 12 and 13) STEERING WHEEL TEST (Press SERVICE switch to select 11 then press RESET switch) Check the Optic sensor functions on Steering Wheel Assy. LED Display shows digits from 0 to 48 when the Optic sensor is activate. Spin the wheel to move the digits, this means the Optic sensor works fine. SWITCH TEST (Press SERVICE switch to select 12 then press RESET switch) Check the Coin switch and Magnet under the CAR Assy. If the Magnet is positioned properly and Coin Switch is OFF, Display shows "0". When the Coin Switch is ON, Display shows "1" then Lamp #1 on the Marquee will be ON. Lock out coin of Coin mech will work, too. When the Magnet is OFF, Display shows "2" and Lamp #3 on the Marquee will be ON. LAMP TEST (Press SERVICE switch to select 13 then press RESET switch) Check the 9 Lamps and LED Display PCB on the Marquee. They automatically Light up and count up. 7 MECHANISM TEST Display shows 2­ then press SERVICE switch to select following TEST MENU. UNIT TEST (Press SERVICE switch to select 21, then press RESET switch. ) X-MECH is controlling the CAR Assy by Magnet base and Motor. Spin the Steering Wheel to move the Magnet base with Car Assy left and right. When the Left & Right Limit Sensor in the XMECH is activated, Lamp #1 or #9 on the Marquee will light up. [. . . ] If error is not cleared, need to exchange the Main PCB. Check wiring and pin connection of XMech. LED BOARD Connector S +5VDC DATA CLK LATCH GND 12VDC 1 2 3 4 5 6 1 2 3 4 5 6 7 120VAC to Bill Acceptor Connector L +5VDC DATA CLK LATCH GND 1 2 3 4 5 +5VDC +5VDC +12VDC +12VDC +24VDC +24VDC GND GND GND GND 1 2 3 4 5 6 7 8 9 10 Connector P FUSE 3 Amp SB MAIN SWITCH LINE IN 120VAC, 60Hz BLK WHT GND DME34BML30B M 1 2 D 24VDC Motor +5VDC OUTPUT GND RESET Switch SERVICE Switch Speaker 8 ohm 5 W + ENCORDER MOTOR PCB TA8428K Magnet SW Magnet SW Limit sensor (L) LG-217 Limit sensor (R) LG-217 +5VDC GND OUTPUT +5VDC GND OUTPUT X-MECH. [. . . ]