User manual SAMSUNG NP350E5C-A01

[. . . ] It might abnormally function at a place over 2000m in height, so do not install and operate there. Heat on the top of the PDP Display The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product. [. . . ] or button after selecting the by pressing the or ENTER ( ) button. : Magnify the size of the picture vertically on screen. 16:9 Wide 4:3 Move Enter Return Zoom 4:3 PC to DVI Mode Size 16:9 Wide 4:3 Zoom 4:3 6 7 Press the ENTER ( Press the EXIT button to exit. You can select these options simply by pressing the P. SIZE button on the remote control. If you change the picture size when PIP is On, PIP will automatically be turned Off. Depending on the input source, the P. SIZE options may vary. PC and DVI modes, only 16:9 & 4:3 modes can be selected. Move Enter Return Positioning and Sizing the screen using Zoom Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction using the . . . or button after selecting the by pressing the oe or button. Resize the screen vertically using the . . . or button after selecting the by pressing the oe or button. button extends it upward and pressing the button extends it downward. ) Screen enlargement operates only in Video/S-Video/ Component input modes. PC/DVI modes prevent the screen enlargement function. English - 21 Freezing the Current Picture You can freeze the picture when watching a moving picture simply by pressing the "STILL" button. To cancel the Remote Control Button Lock, press "0000" using the numeric buttons on the remote control then, `IR LOCK : OFF' is display. English - 26 Setting Up Your Personal ID Number This feature sets viewing restrictions and prevents unauthorized access to your PDP Display through the PIN (Personal Identification Number), which is a 4 digit number. Safety Lock Function Screen Burn Protection Multi Control Video Wall Fan : Off 1 Press the MENU ( Result: ) button. The main menu is displayed. 2 Press the or button to select Function. ) button. Key Lock IR Lock Change PIN Move Enter Return 3 4 5 6 Press the ENTER ( Safety Lock : Off Press the or button to select Safety Lock. Press the or button to select Change PIN. Press the number buttons to enter your current 4-digit pin number. 7 8 Move Enter Return The default pin number for a new PDP Display set is "0000". Change PIN Press the numeric buttons to enter your new 4-digit pin number. Re-enter your new pin number to confirm. Press the EXIT button to exit. Enter PIN Enter New PIN If you forget the pin number, press the remote control buttons in the following sequence, which resets the pin to 0-0-0-0: MUTE, 1, 8, 6. 0 . . 9: Enter PIN Return Change PIN Enter PIN * * * Enter New PIN * 0 . . 9: Enter PIN Return English - 27 Setting the MDC (Multiple Display Control) This function enables you to easily control the connected PDP Displays on the PC by specifying IDs to connected PDP Displays. Function Screen Burn Protection Safety Lock Multi Control Video Wall Fan : Off 1 Press the MENU ( Result: ) button. The main menu is displayed. 2 Return Press the or button to select Function. ) button. Move Enter 3 Multi Control ID Setup ID Input : : 00 -- Press the ENTER ( 4 5 Press the or button to select Multi Control. Press the ENTER ( Result: ) button. The Multi Control menu is displayed with the ID Setup selected. 6 Move Enter Return Press the ENTER ( ) button again. Select the ID setup number by using the numeric buttons. [. . . ] In 1360 x 768 resolution, the screen displays 1360 pixels horizontally. A "" mark means that this mode can be supported. A " " mark means that this mode is recommended. In DVI mode, this product does not support DDC in DTV format (1080i/720p/480p); some of DVD/STBs supporting DTV format may display the poor picture. [. . . ]