User manual SAMSUNG SYNCMASTER 151P

[. . . ] SyncMaster 151P/171P Main Page On-Screen Display Safety Instructions Notational Power Installation Cleaning Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Specifications General Specifications PowerSaver Preset Display Modes Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Information Service Terms Regulatory Natural Color For Better Display Authority Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Notational When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Power Installation Clean Other Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. [. . . ] If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. The location and the position of the monitor may influence the quality and other features of the monitor. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or an "Video mode not supported" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. General Model Name General PowerSaver Preset Timing Modes SyncMaster 151P LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16. 7M (True) Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0. 7 Vpp positive at 75 ohms Separate H/V sync, Composite, Sync-On-Green TTL level positive or negative Maximum Pixel Clock 80 MHz Power Supply AC 90 to 264 VAC, 60/50Hz ± 3Hz Signal Cable 15pin D-sub cable, DVI-D cable, DC-cable attachable Power Consumption Max. 30W Dimensions (WxDxH) / Weight 398, 2 X 208, 4 X 443, 2 mm / 4. 6kg(With Simple Stand) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99. 999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. of TFT LCD pixels that is contained in this product are 2, 359, 296. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system Interaction of the monitor and system. computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing 1024 x 768@60Hz 1024 x 768@75Hz 30 ~60kHz 56~75Hz 15. 0 inch diagonal 304. 1(H) x 228. 1(V) 0. 297(H) x 0. 297(V) a-si TFT active matrix 80/80/80/70(L/R/T/B) SyncMaster 151P General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. [. . . ] Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup. exe and then press the <Entrer> key. (If the drive where the CD is inserted is not D:\, enter the applicable drive. ) How to delete the Natural Color software program Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program]. [. . . ]